Kenmore Dishwasher Spray Arms

Videos!

Your Price

$35.34

Kenmore Dishwasher Lower Spray Arm

★★★★★

123 Reviews

PartSelect Number PS12585623

Manufacturer Part Number 5304517203

The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broken (due to general wear or high heat), it should be replaced. Your lower spray arm will be located at the bottom of your dishwasher tub. Check your user manual and model number to ensure this model is right for you. This version is plastic and metal and comes in gray/blue. We recommend you wear work gloves to keep your hands safe when installing and disconnect power to the appliance. You will also want to make sure that you turn off the water supply to your dishwasher. From here, you will want to open the dishwasher, pull out the lower rack and set it aside. Remove the lower wash arm. On each side of the bottom of the spray arm, there are small locking tabs that can be pushed aside using a flathead screwdriver. Once released, the spray arm can easily be pulled off the dishwasher. Put the new lower wash arm in place and push it down to lock it in. Ensure it is spinning freely and does not hit the heating element. Return the lower dish rack into place and then close the dishwasher door.

Fixes these symptoms

Leaking
Noisy
Not cleaning dishes properly
See more...

Installation Instructions

Donna from Madison, OH

spray arm keeps melting

I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done.. Read more...

Your Price

$41.21

Kenmore Dishwasher SPRAY ARM

★★★★★

70 Reviews

PartSelect Number PS12705424

Manufacturer Part Number 5304518927

This lower spray arm assembly is a device in your dishwasher that distributes water and detergent during the washing cycle. Its rotating motion sprays water in multiple directions, ensuring thorough cleaning. Typically, it is attached to a support or hub at the bottom of the dishwasher. When this part is broken, there are noticeable signs to be aware of. You might hear knocking or banging sounds coming from the dishwasher. The spray arm may be wobbly or unable to rotate. If a broken arm assembly is not replaced, your dishes may still have dirt on them even after a wash cycle. Additionally, leftover food residue can result in an unpleasant smell within the dishwasher. To remove the existing arm assembly, simply grasp the center of it and lift it up so that it unsnaps from your dishwasher. Please note that this OEM-sourced part is sold individually.

Fixes these symptoms

Leaking
Noisy
Not cleaning dishes properly
See more...

Installation Instructions

Allison from Greenville, SC

Melted spray arm resulted in leaky dishwasher

Over Thanksgiving, the spray arm in my dishwasher apparently popped off and was partially melted. I remounted it inside the dishwasher, but the new hole was on the side of the arm. I think this resulted in water being sprayed directly against the door and not up through the top holes. It flooded my kitchen floor.

The spray arm pops on and off with plastic tabs (?) at the base. You can lightly pry with a butter knife or simply wiggle it off. The new one popped right on. Easiest repair EVER. Read more...

Videos!

Your Price

$27.12

Kenmore Dishwasher Middle Spray Arm Kit

★★★★★

128 Reviews

PartSelect Number PS382824

Manufacturer Part Number 675808

This middle spray arm kit includes an upper spray arm, a holder or hanger, water supply tube or delivery tube, split ring seal, and a screw. The function of these parts is to spray water to all levels of the dishwasher so the dishes will come out completely clean. This kit has recently been redesigned. It does not include the upper support or mount, so consider ordering those parts as well if necessary. The spray arm is approximately 18 inches long, and all parts are white in colour. The only tool you will need to complete this repair is a Phillips screw driver.

Fixes these symptoms

Door won’t close
Leaking
Noisy
See more...

Installation Instructions

Robert from York, PA

Lower spray arm was not turing properly and causing poor wash results

I noticed the upper bushing washer was worn thin. this caused the lower spray arm to rise too high and wobble during all the wash cycles. Also the rotation of the lower spray arm was wearing grooves in the lower bushing.

I removed the retaining nut and simply replaced teh defective parts. While I was at it I figured equal wear might be evident on the upper spray arm so I bought a complete rebuild kit to bring all rotational parts back to new and equal preformance that was achieved by removing the ss screw and removing the upper spray arm, bushing and clip then replacing them in the order of removal. Noticed a huge difference in the quality of the washed dishes!! Thanks Parts Select 100% to yoru company!! Read more...

Videos!

Your Price

$11.26

Kenmore Dishwasher Lower Spray Arm Support

★★★★★

17 Reviews

PartSelect Number PS12712289

Manufacturer Part Number 5304518968

This lower spray arm is a genuine OEM part for various makes and models of dishwasher and is sold as an individual part. This part attaches to the lower spray assembly of your dishwasher and the lower spray arm itself clips into this part to facilitate its spinning movement during the washing cycle. To replace it, remove the spray arm by pulling it out, remove the surrounding circular clip and then twist to remove this bit. Made completely of plastic, this part measures approximately 3-inches deep, 2-inches wide, and 3.125-inches tall.

Fixes these symptoms

Leaking
Noisy
Not cleaning dishes properly
See more...

Installation Instructions

Dale from Worley, ID

spray arm fell off and melted on element

The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strainer basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max. Read more...

Your Price

$54.17

Kenmore Dishwasher Middle Spray Arm

★★★★★

15 Reviews

PartSelect Number PS11755664

Manufacturer Part Number WPW10498900

This is a replacement middle spray arm in your dishwasher. You will find your middle spray arm mounted on the bottom of the middle dish rack. The upper spray arm rotates and sprays water during the operating cycle. If your dishes are not coming out of the dishwasher clean, you may have a malfunctioning middle spray arm. Debris and hard water buildup in your dishwasher can cause the middle spray arm to clog. To replace the spray arm, simply turn the arm counter clockwise to release it from the dish rack. Screw in the new spray arm to complete the repair. This part is sold individually.

Fixes these symptoms

Leaking
Not cleaning dishes properly
See more...

Installation Instructions

robert from INDIANOLA, IA

replace middle spray arm and water srayer

remove 2 locks on metal roller guides. remove top basket. turn upside down on counter.remove spray arm by pryng one side in and lift out then push other side down and the out. install same as removal. line spray arm and turn clockwise til you hear a click.install basket and install locking plugs. Read more...

Videos!

Your Price

$10.38

Kenmore Dishwasher Upper Spray Arm Mount

★★★★★

60 Reviews

PartSelect Number PS11746245

Manufacturer Part Number WP8539324

This upper spray arm mount has been redesigned by the manufacturer, so it not longer requires a clip and screw to be installed. To replace this part, first remove the rack stops from the upper dish rack and pull out the dish rack to work on it. Remove the screw holding the spray arm in place, take off the spray arm and slide out the feeding tube. Flip the rack over to remove the mounting bracket from the mount. Snap the new mount into place and replace the other parts.

Fixes these symptoms

Door won’t close
Leaking
Noisy
See more...

Installation Instructions

Sibyl from Sparta, NJ

The top spray arm of my dishwasher broke off in my hand.

I removed the screw holding the spray arm to the bracket. I then put on the new bracket and tightened the screw. The bracket just clips on to the top basket of the washer. Easy as pie. Read more...

Videos!

Your Price

$36.11

Kenmore Dishwasher Upper Spray Arm

★★★★★

71 Reviews

PartSelect Number PS11770483

Manufacturer Part Number 5304506516

This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwasher. No tools are required for this repair, simple remove the rack stops and upper dish rack, then disassemble the mount and spray arm before installing the new one.

Fixes these symptoms

Leaking
Noisy
Not cleaning dishes properly
See more...

Installation Instructions

Roy from Worcester, MA

The spray arm would fall off during the washing cycle.

Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components. Read more...

Videos!

Your Price

$8.00

Kenmore Dishwasher Lower Sprayarm Nut

★★★★★

22 Reviews

PartSelect Number PS11745480

Manufacturer Part Number WP8268873

This spray arm nut is used in dishwashers and works as the retaining nut for the lower dishwasher spray arm. The nut makes sure the lower spray arm is secured to the pump housing. If your spray arm is coming off, or your nut is lost or damaged, replacing the part can be a solution to your problem. Remember to unplug dishwasher from power source and disconnect the water supply before you begin this installation. Refer to the manual provided by the manufacturer for further installation instructions.

Installation Instructions

patricia from Chicago, IL

Lower sprayarm nut stripped + broken inside Pump outlet

You WILL need a star-tip screwdriver for this COMMON DU915 repair. We already had one.
The plastic "wing" nut which keeps the lower sprayarm attached to the pump assembly cracked inside where the threading on each part meets. Have been reattaching the nut to the Pump outlet for a year or so with super glue and finally found PartSelect.com. My husband had to fix this with a star screwdriver and vice grips (and he is super strong)-- otherwise an easy fix using just the manual supplied by the manufacturer. I just noticed the virtual repairman feature on partselect but we didn't need to go there.
The starhead screws that hold the pump outlet in place were on super tight. Other than that, no problem. It has been a week and the dishwasher works like new.
I ordered the parts online at 9pm at night and had the parts in my mailbox the next day - LESS than 24 hours later. How is that even possible?
Just ask anyone who knows me...I am NOT easy to please when it comes to customer service in any realm of the retail world - I have to say without any doubt PartSelect is the BEST experience I've had in my entire shopping life. It's as if customers run this company. I only wish they sold car parts, groceries, clothes and food.
I will be back to purchase again, I'm sure and I know it will go just as smoothly.
PartSelect.com...Please call me when you are ready to launch an IPO!!!!!!! Read more...

Videos!

Your Price

$15.96

Kenmore Dishwasher Lower Sprayarm Seal

★★★★★

11 Reviews

PartSelect Number PS11741334

Manufacturer Part Number WP3376846

This dishwasher lower spray arm seal, or under spray arm bearing ring, is designed with the split by the manufacturer. It is not damaged or defective, and is sourced directly from the original manufacturer. This part is approximately 2 inches in diameter, made of plastic, and is white in color. This part is mounted underneath the dishwasher spray arm and creates a seal between the lower spray arm and the sump housing. To access the seal, remove lower dish rack and unscrew the nut that secures lower spray arm to the remove cover. No tools are required to replace the lower seal on your dishwasher.

Fixes these symptoms