Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
Cub Cadet Lawn Mower Engines
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
![Cub Cadet Appliance Parts](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/brands/250/cub-cadet.png)
Popular Cub Cadet Lawn Mower Engines
Cub Cadet Lawn Mower Gear-Governor
PartSelect Number PS9151758
Manufacturer Part Number 793338
Installation Instructions
rodney from MUSCATINE, IA
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet to remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read more...
Cub Cadet Lawn Mower Rod-Push (Steel)
PartSelect Number PS9062983
Manufacturer Part Number 690981
This is a replacement steel push rod for your lawn tractor engine. The engine will have two push rods; one made of steel, and one made of aluminum. This part is made of steel and is approximately 6 inches in length. Make sure you order the correct replacement rod, as they are different. If the engine is unable to operate at full power, you may have a bent or broken push rod. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Engine misfires
- See more...
Installation Instructions
Robert from WHITMAN, MA
the head blew a vaulve guide destoying push rods
about 6 hours to tear down and replace don't do it in the hot sun needed more breaks takes longer, but the new factory heads did it started up 185 lbs of compression almost back to new, so much more power than old one's. FYI take off the motor cover every year clean out the debris (grass-mouse nest- and oil) it blocks the air and COOKS THE HEAD it only takes short time and will make that motor last a little longer but it is a BRIGGS engine
Read more...
Cub Cadet Lawn Mower Adjuster--Rocker Arm
PartSelect Number PS9066105
Manufacturer Part Number 691986
Cub Cadet Lawn Mower Rod-Push (Exhaust)(Aluminum)
It was simple just watch what you do. Also make sure you lash the value. U tube it. Read more...
PartSelect Number PS9063658
Manufacturer Part Number 691758
Installation Instructions
GERALD from CLIO, MI
Exhaust push rod
Reverse of how i took broken exhuast value out.It was simple just watch what you do. Also make sure you lash the value. U tube it. Read more...
Related Cub Cadet Lawn Mower Parts
- Cub Cadet Lawn Mower Bearings
- Cub Cadet Lawn Mower Brackets and Flanges
- Cub Cadet Lawn Mower Caps and Lids
- Cub Cadet Lawn Mower Carburetors
- Cub Cadet Lawn Mower Dipsticks
- Cub Cadet Lawn Mower Filters
- Cub Cadet Lawn Mower Hardware
- Cub Cadet Lawn Mower Hoses and Tubes
- Cub Cadet Lawn Mower Seals and Gaskets
- Cub Cadet Lawn Mower Springs and Shock Absorbers
- Cub Cadet Lawn Mower Starters