Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
Models
>
66512773K312
66512773K312 Kenmore Dishwasher - Overview
Sections of the 66512773K312
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Retainer Clip - Black
PartSelect #: PS11755736
Manufacturer #: WPW10503548
This part is used to hold the access panel in place. Sold individually.
$26.79
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Dishwasher INLET VALVE
PartSelect #: PS12578165
Manufacturer #: W11175771
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$64.14
In Stock
Seal
PartSelect #: PS11755651
Manufacturer #: WPW10497235
This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The ...
$11.16
In Stock
Retainer Clip - White
PartSelect #: PS11755737
Manufacturer #: WPW10503549
This part is used to hold the access panel in place. Sold individually.
$7.42
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.02
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.12
In Stock
Drain Hose
PartSelect #: PS11756139
Manufacturer #: WPW10545278
This part is used to drain water from your dishwasher.
$48.31
In Stock
Push-In Retainer Clip
PartSelect #: PS11741622
Manufacturer #: WP3400918
Sold individually.
$39.04
In Stock
Side Mounting Bracket Kit
PartSelect #: PS1487167
Manufacturer #: 8212560
This mounting kit can be used on solid surface countertops.
$18.69
In Stock
Upper Spray Arm
PartSelect #: PS11752935
Manufacturer #: WPW10327455
The upper spray arm rotates and sprays water to clean the dishes inside the dishwasher tub. If your dishes are not being cleaned properly, you should check if there is an issue with the spray arm. To ...
$59.62
In Stock
Inlet Fill Hose
PartSelect #: PS11738178
Manufacturer #: W10878507
This fill hose is a genuine OEM replacement part for your dishwasher. The hose is made of black plastic, and is accordion-style, for ease of movement within your dishwasher. To replace the fill hose, ...
$77.42
In Stock
Questions And Answers for 66512773K312
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
May 1, 2023
Kenmore elite dishwasher continues to run
For model number 66512773K312
Hello Bob, thank you for your question! Based on the description that you have provided, we would recommend you replace the control board, part number PS11759622, to fix the issue. We hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the 66512773K312
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door leaking from corner.
First, I replaced the bottom door seal. You will need magnetic nut drivers because of the location of the 3/16 screws that hold the seal in place. you also need a 1/4 in nut driver to remove plastic cover that covers up the 5 3/16 screws. Last you need a small star driver to remove the door screws. Note 4 of the door screws, the 4 on top
... Read more
of the door are much longer than the side screws. With all this said, this seal was not my problem. I then replaced the large black rubber seal around the tub. Be sure if you do this you fold the seal in half and start in the middle of the top of the opening so you have the exact amount of seal left over on both sides. Also when you remove the old seal, clean the area it was removed from with a damp cloth. Turns out, That was not my problem either. So now I will move to the next step to see where the water is coming from but maybe this information will help someone with a simple door leak.
Read less
Parts Used:
-
Don from GRAPEVINE, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
39 of 44 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Parts Used:
-
Michelle from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
65 of 130 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inlet valve wasn't working
Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done
Parts Used:
-
Melissa from AIKEN, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
25 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!