Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
$33.94
In Stock
Order within the next 6 hrs and your part ships today!
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$54.38
In Stock
Order within the next 6 hrs and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Order within the next 6 hrs and your part ships today!
This suspension rod kit is a genuine OEM replacement kit that is compatible with various models of washing machine. The kit is responsible for supporting the inner tub of the washing machine and absor...
$113.57
In Stock
Order within the next 6 hrs and your part ships today!
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Order within the next 6 hrs and your part ships today!
This is a shift actuator, and is designed for use in washing machines. This shift actuator is made to change the mode of the motor between spin and agitate, as well as communicate with the control boa...
$67.48
In Stock
Order within the next 6 hrs and your part ships today!
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Order within the next 6 hrs and your part ships today!
Order within the next 6 hrs and your part ships today!
Questions And Answers for 11025132410
Ask our experts a question about this model and we'll get back to you as soon as possible!
13 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
March 4, 2020
It gets to the rinse part of the cycle, then never finishes. It will add water an agitate and keep doing that. One time I checked it after a while because it wasn't finished yet and the tub was almost full of water. I stopped it, unplugged it, then plugged it back in and set dial to drain and spin, which it did, so I could take the clothes out. Help please !
For model number 11025132410
Hello David, Thank you for the question. This could be a defective Washer Electronic Control Board, PartSelect Number PS10057020 not going through the cycles properly on its own. We hope this helps.
Will wash but will not rinse or spin. Timer does not advance could this be the timer
For model number 11025132410
Hello Mary, Thank you for the question. If the Timer is not advancing, it normally indicates the Timer Control Board will need to be replaced. We hope this helps!
Hi Dorian, thank you for your question. You may want to test your water inlet valve. The valve can be tested with a multi meter and should be reading between 500 - 1500 ohms of resistance. Good luck with your repair.
Was this helpful?
Thank you for voting!
Dave
November 4, 2023
I have a Kenmore washer with low profile agitator. Should the agitator spin freely on the shaft? If I lift it up a 1/4" or less then it catches and spins with the tub. I am not sure if it should be free spinning or not.
For model number 11025132410
Hi Dave, thank you for the question. Based on our understanding of the issue, we would suggest replacing the gearcase, part number PS16220911, to solve the problem. It drives the agitator and spins the basket in the washer. We hope this solves your problem!
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.