KitchenAid Microwave Oven Combo Hinges

Your Price

$54.66

KitchenAid Microwave Oven Combo Door Hinge - Left Side

★★★★★

3 Reviews

PartSelect Number PS11747290

Manufacturer Part Number WP9760574

This hinge is for a stainless steel door and is located on the left side of the oven door.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Tony from HAYDEN, ID

door hinges worn out oven door not fully closing

Remove and replace oven door hinges. Disassembly of oven door unit required. Step by step instructions available on youtube. Read more...

Your Price

$56.92

KitchenAid Microwave Oven Combo Door Hinge - Right Side

★★★★★

1 Review

PartSelect Number PS11747291

Manufacturer Part Number WP9760575

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

William from Dumfries, VA

Inside oven door glass was broken and door was not closing completely.

I removed the door from the oven by locking the hinges with the built-in locks leaving the door open about 20 degrees. the door can then be lifted slightly off the hinges and pulled out at the bottom while tilting the top inward to remove it from the oven. With the door laying on a suitable surface with the outside face down, I removed about 6 or 8 screws from the door inside panel freeing the springs and the inside panel from the middle and front panels. Care must be taken to note from which locations the pointed self-taping screws come as opposed to the narrower-thread machine screws that hold the springs. Note: The inside panel does not need to be removed! Once the inside panel is freed from the inner panels, using suction cups the glass can be lifted slightly and slid toward the bottom of the door, rotated slightly, and removed through the window hole in the back face of the door. The new glass is installed in a similar way using suction cups by maneuvering it at a angle through window hole and into its frame. The hinges were replaced by lifting the bottom of the inner door panel slightly to clear the hinge and swapping in the new ones. Be sure to observe the difference between the left and right hinges in the location of the screw hole at the bottom of each hinge The narrow-thread machine screws that hold the hinges to the inside panel should be installed first while you can get you hand inside the door to hold each hinge in alignment with the screw holes while you start each screw. Re-install the pointed self tapping screws by pressing down on the rear panel to collapse the spring-action glass frames within the door so that the short screws will reach their threaded hole. Be careful to back off the self tapping screws first until you feel a click into the original threads to avoid stripping the holes. Last re-install the door on the oven. The replacement hinges should have come with the springs already "cocked" with the built in locks in place. Install the door with it in tan almost-closed position by sliding the hinge extensions into the slots in the oven. Once the extensions are properly in the slots the door can be fully opened and the built-in hinge locks re-positioned to the unlocked position to allow the door to fully close. Should you accidentally release only one of the hinge locks in trying to insert the hinge extensions into the slots you will have to reset the hinge. If the door is free from the oven, this may require a pair of heavy pliers, like channel lock pliers, to re-tension the hinge spring and "cock" the hinge extension by re-positioning the built-in lock in the locked position. If the hinge lock on one side of the door releases, but the the opposite side hinge extension is not fully inserted into the oven slot I recommend carefully moving the door to the fully open position, being careful to avoid twisting the inserted spring's extension, so that the hinge lock can be re-positioned to the locked position, the door full removed, and start again to install it. It helps to have two persons to hold opposite sides of the door for this operation as the door is heavy, but not essential. When in the proper position the hinge extensions may not appear fully inserted, but this is normal to allow for closing of the built in locks. It helps to observe how much of the hinge extension is exposed either before removing the door initially, or, if you have a double oven, looking at the hinges on the door of the other oven. Good luck with your repair. Read more...

Your Price

$57.96

KitchenAid Microwave Oven Combo Door Hinge - Left or Right Side

PartSelect Number PS11742640

Manufacturer Part Number WP4455524

This hinge is used for white and black models.

Fixes these symptoms

Door won’t close
See more...

Your Price

$60.52

KitchenAid Microwave Oven Combo Door Hinge

★★★★★

5 Reviews

PartSelect Number PS11742641

Manufacturer Part Number WP4455525

This is a door hinge for the oven door on your range. It allows the door of your unit to open and close without much effort. This hinge will also allow the door to stay open at different angles and hold that position. This part is sold individually and it works for both the left and the right side of your unit. You may need to replace this part if you are noticing that your appliance will not hold the open or closed positions properly.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

John from Columbus, KS

built-oven door wouldn't close all the way

First, insert pins or screws in the holes at the hinge pivot point. Then lift and pull the door out. Four screws remove the door front(2 top,2 bottom). Two screws remove each hinge. After installing the hinges, put the door front back on. Set the door back in the hinge slots, open the door all the way and remove the factory installed hinge pins and you're finished. Read more...

Your Price

$10.68

KitchenAid Microwave Oven Combo Oven Door Hinge Pin

★★★★★

2 Reviews

PartSelect Number PS11740692

Manufacturer Part Number WP307986

This hinge pin is sold individually.

Installation Instructions

Mark from Leawood, KS

Broken Oven Door

This is an easy fix. Just before the holidays, it was imperative that this appliance be in top shape. Since the door 'hung' wrong, it was determined that the hinge pin broke. Remove the 2 phillips head screws on the door and open the door to the to a 15 degree opening. This position allows you to slip the door off the hinge levers. Now that the door is off, replace the hinge pin and slip the retainer ring on with a screw driver blade to push it on the pin. Slide the door back on the levers and fasten the retainer screws. DONE! Read more...

Your Price

$48.89

KitchenAid Microwave Oven Combo Door Hinge - Right Side

★★★★★

1 Review

PartSelect Number PS11747293

Manufacturer Part Number WP9760577

This hinge is for a stainless steel door and is located on the right side of the oven door.

Fixes these symptoms

Door won’t close
See more...

Your Price

$70.35

KitchenAid Microwave Oven Combo Door Hinge - Left or Right Side

PartSelect Number PS11742642

Manufacturer Part Number WP4455526

This is a door hinge for the oven door on your range. Are you having troubles opening and closing your oven door? Do you find that it is sticking, or is too loose, and not staying in place at all? If that is the case, you may want to replace the hinges on your appliance. This model is used with stainless steel ranges only. It includes the coiled spring and may be used for either the left or the right side of your unit and is sold separately. It is recommended that you change both hinges at the same time.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Michael from Manalapan, NJ

Oven door was not closing completely.

Removed the oven door from the oven using the KitchenAid supplied tool to hold the spring in position. There was a hole at the bottom of the hinge and if you insert this KA tool it would keep the hinge from closing completely which allowed you to pull the door away from the oven. Removed the 4 screws that held the front (glass cover) from inside part of the oven door.
Used the pliers to pull the hinge back to remove the KA tool and then unscrewed the 2 screws holding the hinge in place. Did the same on the other side. Installed the hinge into place and re-installed the glass front of the oven door. Place the oven door into the oven and when you open the door completely (down) the 2 holding pins are removed - similar to the KA tool.

Took about 30 minutes from start to finish. Used the parts list (found online) to see what screws I had to unscrew.

Searched online found PartSelect had good price, confirmed over the phone that the hinges were not a set (needed 2). Completed order online and part delivered in 2 days. Have used PartSelect twice for me oven. The Kitchenaid oven is another story - horrible - thank goodness for PartSelect. Read more...

Your Price

$61.92

KitchenAid Microwave Oven Combo Door Hinge - Left Side

PartSelect Number PS11747292

Manufacturer Part Number WP9760576

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

William from Dumfries, VA

Inside oven door glass was broken and door was not closing completely.

I removed the door from the oven by locking the hinges with the built-in locks leaving the door open about 20 degrees. the door can then be lifted slightly off the hinges and pulled out at the bottom while tilting the top inward to remove it from the oven. With the door laying on a suitable surface with the outside face down, I removed about 6 or 8 screws from the door inside panel freeing the springs and the inside panel from the middle and front panels. Care must be taken to note from which locations the pointed self-taping screws come as opposed to the narrower-thread machine screws that hold the springs. Note: The inside panel does not need to be removed! Once the inside panel is freed from the inner panels, using suction cups the glass can be lifted slightly and slid toward the bottom of the door, rotated slightly, and removed through the window hole in the back face of the door. The new glass is installed in a similar way using suction cups by maneuvering it at a angle through window hole and into its frame. The hinges were replaced by lifting the bottom of the inner door panel slightly to clear the hinge and swapping in the new ones. Be sure to observe the difference between the left and right hinges in the location of the screw hole at the bottom of each hinge The narrow-thread machine screws that hold the hinges to the inside panel should be installed first while you can get you hand inside the door to hold each hinge in alignment with the screw holes while you start each screw. Re-install the pointed self tapping screws by pressing down on the rear panel to collapse the spring-action glass frames within the door so that the short screws will reach their threaded hole. Be careful to back off the self tapping screws first until you feel a click into the original threads to avoid stripping the holes. Last re-install the door on the oven. The replacement hinges should have come with the springs already "cocked" with the built in locks in place. Install the door with it in tan almost-closed position by sliding the hinge extensions into the slots in the oven. Once the extensions are properly in the slots the door can be fully opened and the built-in hinge locks re-positioned to the unlocked position to allow the door to fully close. Should you accidentally release only one of the hinge locks in trying to insert the hinge extensions into the slots you will have to reset the hinge. If the door is free from the oven, this may require a pair of heavy pliers, like channel lock pliers, to re-tension the hinge spring and "cock" the hinge extension by re-positioning the built-in lock in the locked position. If the hinge lock on one side of the door releases, but the the opposite side hinge extension is not fully inserted into the oven slot I recommend carefully moving the door to the fully open position, being careful to avoid twisting the inserted spring's extension, so that the hinge lock can be re-positioned to the locked position, the door full removed, and start again to install it. It helps to have two persons to hold opposite sides of the door for this operation as the door is heavy, but not essential. When in the proper position the hinge extensions may not appear fully inserted, but this is normal to allow for closing of the built in locks. It helps to observe how much of the hinge extension is exposed either before removing the door initially, or, if you have a double oven, looking at the hinges on the door of the other oven. Good luck with your repair. Read more...

Your Price

$53.74

KitchenAid Microwave Oven Combo Door Hinge

★★★★★

2 Reviews

PartSelect Number PS11742639

Manufacturer Part Number WP4455523

Includes the coiled spring and can be used for either left or right side of appliance. Sold individually.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

David from San Jose, CA

Hinges needed to be replaced having been overstrained

I paid for an online advice service (Just answer)after failing to remove the hinges. The advice was not remotely helpful and I have asked for my deposit back.

Here are the steps:

Remove the door: Place the two tiny studs taken from the tongues of the new hinges in the same holes in the old door.
Holding the door just open, lift up and out to remove the door from the oven.

Lay the door on its inside surface, then remove 2 Phillips head screws from both the top and bottom edges of the door to release the front glass assembly. The hinges can now be seen.

Turn the door over and remove four Phillips heads screws to release the hinges, replace with new hinges.

Replace the two small studs in the hinge tongues and replace the door reversing the removal process. Remove and save the two studs (handy if you ever want to clean the glass on the inside) Read more...