Washer Dryer Combo Thermostats
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Washer Dryer Combo Thermostats
Your Price
$19.63
In Stock
Washer Dryer Combo Dryer Thermal Fuse
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes. Read more...
PartSelect Number PS11741460
Manufacturer Part Number WP3392519
The Dryer Thermal Fuse (Thermal Cutoff, Temperature Fuse) is a 2 by ½ inch, white, plastic safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is designed to handle. This can occur when a heating element is shorted, a regulating thermostat or thermister fails, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16 inch terminals.
Fixes these symptoms
- Heat stays on after drum has stopped
- Not Heating
- Too hot
- See more...
Installation Instructions
ANTHONY from CHESHIRE, CT
Dryer was working, but no heat.
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes. Read more...
Your Price
$27.97
In Stock
Washer Dryer Combo Dryer Cycling Thermostat
PartSelect Number PS11741405
Manufacturer Part Number WP3387134
This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heater also allows this thermostat to provide a low heat temperature of approximately 140 degrees when the low temperature setting is selected. The part measures 2 by 1.5 inches, comes in black/silver and is constructed of plastic and metal. The thermostat attaches to the blower wheel housing.
Fixes these symptoms
- Heat stays on after drum has stopped
- Not Heating
- Too hot
- See more...
Installation Instructions
Tom from High Point, NC
Dryer blew cold air.
PartSelect is great for providing parts as requested. Unfortunately, neither of the 2 parts I ordered were on my machine. My bad for not looking at the actual part instead of the description. A word to the wise!
Read more...
Your Price
$36.58
In Stock
Washer Dryer Combo Thermal Cut-Off Kit
PartSelect Number PS334299
Manufacturer Part Number 279816
The thermal cut-off (Dryer Thermal Cut-Off Fuse Kit, Dryer Thermal Cut-Off Kit) prevents the dryer from overheating when the dryer high limit thermostat fails in a closed circuit condition. This part fails when the heater housing does not have adequate airflow through it; this is normally caused by restriction in the exhaust vent, plugged lint screen, or broken blower wheel. If this part fails, the dryer may not produce any heat. This kit includes one high-limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees), jumper wires, and new female spade terminals. Both components are mounted on the heater housing, and measure approximately 2 inches long and 1.5 inches wide each. This kit comes in silver and is constructed of metal.
Fixes these symptoms
- Heat stays on after drum has stopped
- Not Heating
- Too hot
- See more...
Installation Instructions
Vernon from Niceville, FL
No Heat
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off.
Read more...
Your Price
$24.24
In Stock
Washer Dryer Combo Thermal Fuse
PartSelect Number PS3530485
Manufacturer Part Number 6931EL3003D
This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start. These fuses cannot be reset, so if yours has blown, you will need to replace it. A common reason for the thermal fuse to blow on a dryer is if the exhaust vent on your dryer is restricted or blocked. Hot air will be confined in the dryer and the fuse will trip and stop the electricity from flowing to the gas valve or heating element.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Richard from ORMOND BEACH, FL
Dryer would run with no heat
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal fuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
Read more...
Your Price
$53.28
In Stock
Washer Dryer Combo High Limit Thermostat and Thermal Cut-Off Kit
PartSelect Number PS334387
Manufacturer Part Number 279973
Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.
Fixes these symptoms
- Not Heating
- Too hot
- See more...
Installation Instructions
Vince from Kathleen, GA
Clothes would not Dry
I simply removed the back of the dryer to gain access to the heating element. Once I removed the heating element I figured I would also replace the thermostat and thermal fuse as preventive maintenance.
Read more...
Your Price
$28.85
In Stock
Washer Dryer Combo Thermal Cut-Off Kit
On my particular model, the back does NOT come off and all of my repairs had to be made via the front, bottom panel.
(1) disconnected 6 wires (3 pairs) from the heating element and two thermal sensors
(2) removed entire heating element 'sleeve" which contained both the heating element AND the two sensors. The space is way too tight to try and do this any other way (and I highly recommend this method to save a ton of time and frustration.)
(3) vaccummed out the entire inside of the dryer, clearing all lint and debris, including tons of lint creating a blockage, thus slowing the ability to dry over the years
(4) replaced sensors and heating element
(5) installed heating element & Thermal sensors back inside and reconnected all wires
(6) tested dryer to ensure that heating element lit up and produced heat - it worked beautifully!
Besides fixing the heating issue, cleaning out the clogged lint pipe at the back of the dryer and wall have made the old dryer new again. It's working better than ever! Read more...
PartSelect Number PS334278
Manufacturer Part Number 279769
This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.
Fixes these symptoms
- Not Heating
- Too hot
- See more...
Installation Instructions
Wesley from Boyds, MD
Dryer not heating
Our dryer is 8 years old and had been slowly taking longer and longer to dry clothes, to the point that I was ready to purchase a new one. When the dryer stopped heating completely, I removed the bottom panel and found that the heating element was no longer working. I checked online and found this website. The top two recommended fixes for this issue was to replace the heating element and/or thermal cut-off kit (two sensors). I chose to purchase both, delivered to me very quickly (two days). I figured for $80 you can't go wrong. Here's the procedure I followed:On my particular model, the back does NOT come off and all of my repairs had to be made via the front, bottom panel.
(1) disconnected 6 wires (3 pairs) from the heating element and two thermal sensors
(2) removed entire heating element 'sleeve" which contained both the heating element AND the two sensors. The space is way too tight to try and do this any other way (and I highly recommend this method to save a ton of time and frustration.)
(3) vaccummed out the entire inside of the dryer, clearing all lint and debris, including tons of lint creating a blockage, thus slowing the ability to dry over the years
(4) replaced sensors and heating element
(5) installed heating element & Thermal sensors back inside and reconnected all wires
(6) tested dryer to ensure that heating element lit up and produced heat - it worked beautifully!
Besides fixing the heating issue, cleaning out the clogged lint pipe at the back of the dryer and wall have made the old dryer new again. It's working better than ever! Read more...
Your Price
$85.85
In Stock
Washer Dryer Combo High Limit Thermostat
PartSelect Number PS446428
Manufacturer Part Number 3204267
This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only comes back when it drops by at least 70 degrees Fahrenheit. If your dryer is overheating, taking too long to dry clothes, or is not producing enough heat, replacing the thermostat could be the solution to your problem. The tools needed for this part are a Phillips screwdriver, putty knife, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions and guidance.
Fixes these symptoms
- Too hot
- See more...
Installation Instructions
MELISSA from OKEECHOBEE, FL
dryer does not get very hot, takes two cycle's to dry
removed the screws, disconnected the wires. installed the new elements replaced the wires.
Read more...
Your Price
$45.92
In Stock
Washer Dryer Combo Blower Thermostat
PartSelect Number PS8747887
Manufacturer Part Number 6931EL3002M
The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the air is being measured, it will turn the heat on or off in order to maintain a stable temperature within the drum. The most common reason you would need to replace your thermostat is if your dryer is not receiving enough heat, or any heat at all.The tools you will need to complete this repair include a Phillips screwdriver, and a flat-head screwdriver.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Sheryl from SPRINGFIELD, MO
Dryer not heating
I followed video instruction in disassembling and set screws from each section into diferent small bowls in the order they were removed. Hardest part was some of the screws were really hard to get loose without stripping them and my control panel did not match video but I figured it out. Replacing the parts were easy and putting it back together. While it was apart I cleaned everything including fan blower wheel. Thanks for the right parts and your online video. With your help and a prayer this 62 year old woman fixed the problem and dryer runs like new.
Read more...
Your Price
$45.53
In Stock
Washer Dryer Combo Control Thermistor
PartSelect Number PS1149368
Manufacturer Part Number 134587700
This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. This part is located in the blower housing.
Fixes these symptoms
- Too hot
- See more...
Installation Instructions
Don from RUIDOSO, NM
Dryer cut off before the clothes were dry.
All the symptoms indicated the thermister (located in the exhaust air stream of the dryer) was the problem. Pulled the lower panel off the dryer. Took out the two lower screws holding the door panel on so I could pull the front panel out just enough to get a screwdriver on the screws holding the thermister on. Unhooked the two wires connected to it and hooked them to the new thermister(no need to observe polarity). Put the new thermister in, screwed the door panel back down, put the lower panel on and started drying clothes.
Read more...
Your Price
$51.97
In Stock
Washer Dryer Combo Thermostat Assembly
PartSelect Number PS3530482
Manufacturer Part Number 6931EL3001F
This is a thermostat for various models of LG dryers. This thermostat specifically is the rear high limit thermostat, and it is designed as a safety device to shut off power to your dryer if the internal temperature gets too high. This thermostat comes with a mounting bracket, so you only need the securing screws to fully install it, along with connecting the appropriate wire, after removing the old thermostat. If your dryer is no longer heating properly, or will not start, this thermostat may have been used and is no longer operational. Replacing this thermostat will require you to partly disassemble your dryer, as it is located on the heating element housing. This thermostat is a genuine OEM part and is sold individually.
Installation Instructions
Sheryl from SPRINGFIELD, MO
Dryer not heating
I followed video instruction in disassembling and set screws from each section into diferent small bowls in the order they were removed. Hardest part was some of the screws were really hard to get loose without stripping them and my control panel did not match video but I figured it out. Replacing the parts were easy and putting it back together. While it was apart I cleaned everything including fan blower wheel. Thanks for the right parts and your online video. With your help and a prayer this 62 year old woman fixed the problem and dryer runs like new.
Read more...
