LNC8435A80 Norge Dryer - Instructions

Verified power to the dryer with a volt meter. Identified the high limit fuses under the top cover. I used an ohm meter to determine the fuse located on the heater housing assembly was bad. The fuse located at the top (blue label) was not bad but I changed it since a new one was sent in the kit. Reassembled the dryer and it has been working ever since. Found the problem on a Monday and ordered the part. Received the part on Wednesday and the problem was solved. Cost me about $31. Would have been triple that if a repairman would have been called. Thanks PartsSelect

(Electric) I opened the lid and propped it back on wall. The first piece was located all the way in the back mounted toward you. Easy enough. When it came to the thermal fuse, it was a bit trickier. It's located on the right side of the heating element wall. There is a screw straight on top of the wall. Mine was covered in lint, hence the thermal repair work:) Take the screw all the way out. The fuse is removed by lifting out the thermal fuse mounting bracket. Nothing special holding it in place. Just put the new one in the same way the old one came out. It was a bit difficult to wiggle the bracket back in, but I kept playing enough and it finally lost the battle. Put the screw back in, taking care to make sure it threads on top of the bracket to secure it against the heater element wall. Worked for me! Thanks everyone.

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

Ohmed coils and both had continuity so I changed radiant heat sensor. No bench test for Radiant Heat sensor. Same problem. Changed both coils and dryer works fine. Weak coils were my problem. I read thru the same issues in Parts Select forum and it said Radiant Heat sensor was problem 25% of the time. With coils having continuity and no ohm value specified for coils I made wrong choice but, I have spare parts and look for another 10 years of life in the dryer. Nice to have this forum to research appliance repair. Very helpful for parts location and installation. Dishwasher is next!

loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on

Open the lid, replaced the small fuse on top( one wire at a time). Removed the heating element, then replaced the lower fuse and re-installed the heating element. That part of the job took 15 minutes. The fuses were blown because the plastic housing inside of the front panel was completely clogged. I took the two screws off holding the front panel on, then the two torque screws on the plastic housing. I cleaned a ton of lint out of the housing and re-assembled.

My dryer stopped cold one day, we rushed out and bought a new one. Stuck with a broken dryer I thought I'd take a shot at fixing it (with zero experience). After a few minutes on the internet I found out that a clogged vent can cause it to overheat and blow the fuse. I opened it up and sure enough it was 100% clogged. I replaced the parts that came in the kit and after about 20min it was running like a champ. Now what do I do with the extra dryer?

Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Problem!

Quick fix it works
remove the two screws holding the top from the back. Pull out the top section with the knobs
You should now be able to see the high limit fuse and the heating element.
Remove the two screws holding the fuse to the dryer. Replace the fuse and test before covering.
Also clean up the heating element with a soft brush or blower.

Unplugged electric, turned off gas valve. Opened top using a putty knife, laid it gently back against the wall for support. Removed 2 screws holding front on-leaned front out about 3-4 inches- while holding front with my knees I disconnected door switch wires.-then removed front panel. Followed instructions on maintenance sheet glued on underside of dryer top (Lucky it was there). Took tension off drive belt. Removed belt and drum following instructions on lid sheet. Removed old slides (worn out) Installed new pads & slides. Vacuumed out all lint/dust/dirt I could reach, Cheked rear drum rollers. Reinstalled everything that I had removed. It took extra time to do everything because dryer was in tight space, little working space. Turned gas on, plugged in electric cord. Worked great now.

I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (and the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.

First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i decided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--