Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Trash plunger would go down but not back up
Compactor ram would go to bottom but not return back up after compaction. Keep running until unplugged. After unplugging flipped unit on its side and remover bottom plate (5) nut screws, exposing gears. Found that the main large gear had fine crack which caused it to spin loosely. Ordered gear assembly and lossened four mount screw on motor to move it forward and give slack on chain. Hint: Loosen motor mount bolts, DO NOT REMOVE bolts COMPLETELY! Removed broken plastic gear and reassembled with new. Held/ pushed motor back to retention chain and secured four (4) mount bolts Then reassembled bottom plate with screw nuts and it worked perfectly!!
I have always used compactor bags made of paper & plastic. I was sent bags made of only plastic. I called and was told that is the only kind available. I am concerned that the plastic bags may not be strong enough.
I quest I will have to try these all plastic bags. I hope they are strong enough and work properly.
My very old trash compactor's carrier bag wore out
This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.
Compactor piston stuck in down position and couldn't open!!!
First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!
Compactor draw was not opening fully as the wheel bearings had seized
I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new
Compactor was hard to open had to press hard with foot and lift to open. got harder as it got fuller.
remove the container from base lay on floor unscrew 2 screws one on each side and remove foot pedal. I could see that the foot pedal had small bow in the pedal. You can only see this if you removed. I ordered the rollers in the front but did not install as it is not the rollers. Will keep for future if needed. Replace your foot first if hard to open.
1Turn the compactor off 2Removed the plate on the top of the compactor. Mine was held by 2 screws. Make note of where the electrical connections are located 3Remove the electrical connections on the operating plate. 4Remove 2 screws holding the plate to the compactor the unit housing the operating buttons is now free from the compactor using a small blade move around the outside of the membrane to release the existing cover Clean the lip where glue still exists peel back the plastic cover from the part and press into place Reverse steps 1,2,3 &4
Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering. My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
I flipped this unit over,removed 4 screws to the drive gear.I tore apart found a nut came off the screw rod.Which broke the drive gear.I looked on line found the parts select page.That showed the diagram i needed,to order parts, i needed.The wife and i tackled this task,of repairing this product.The repair was quick and easy.It took less than 30 minutes including cleanup.The wife happy,that all that matters. Jack