KitchenAid Washer Hoses and Tubes
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular KitchenAid Washer Hoses and Tubes
Your Price
$38.93
In Stock
KitchenAid Washer Drain Hose
PartSelect Number PS11753688
Manufacturer Part Number WPW10358149
It connects from the pump to the back panel. The clamp is not included.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Esther from Santa Ana, CA
Drain hose had a leak
The repair was so easy. The part came quickly and with easy to follow directions. I am a woman and a single parent; needless to say, I don't have time or money to waste. This repair cost me under $30 and under 30 minutes to fix. Thank you again!
Read more...
Your Price
$21.96
In Stock
KitchenAid Washer Water Inlet Hose
This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the control panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done! Read more...
PartSelect Number PS11741209
Manufacturer Part Number WP3357328
This part is the replacement water inlet hose for your washer. It is black in color, made of plastic, and is approximately 19 inches long. The water inlet hose connects the water inlet valve to the water fill nozzle. Over time the hose can become cracked and damaged, and this can cause it to leak. A damaged hose will need to be replaced. Be sure to disconnect the water supply to the washer before you begin this repair. You should also determine if any of the other parts that transport water into the washer are leaking, and if they need to be repaired as well. This part is sold individually and is a genuine OEM part.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Timothy from Springfield, VA
Cold water flowed slowly
First, be sure to take the washer apart properly! The first time I fixed my washer I took it apart the hard way to change the clutch, and believe me it took longer to put it back together!This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the control panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done! Read more...
Your Price
$21.29
In Stock
KitchenAid Washer Tub-to-Pump Hose Kit
PartSelect Number PS334685
Manufacturer Part Number 285871
This kit comes with the clamps.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Marc from Morton Grove, IL
Two leaking hoses in my washing machine
Put the machine on its side. Remove old hoses and screw new ones into place. Done in under 20 minutes.
Read more...
Your Price
$62.53
In Stock
KitchenAid Washer Drain Hose
PartSelect Number PS11748248
Manufacturer Part Number WPW10096921
This drain hose is 42" long and includes the clamps.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Francis from Yuba City, CA
I bought a used washer from a friend and they had cut the drain hose short .
I got a pair of channel lock pliers and took off clamp on the hose, after laying wash machine on it's side, poped off a few little clips and replaced the hose, and now everything works perfect.
Read more...
Your Price
$37.52
In Stock
KitchenAid Washer Pump Hose
Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machine requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace. Read more...
PartSelect Number PS11755212
Manufacturer Part Number WPW10467168
This hose attaches to water pump assembly.
NOTE: As per the manufacture if the washer has an Eco Ball, it's no longer needed when the new hose is installed.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
Alexander from Miami, FL
Washer leaking
Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away. Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machine requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace. Read more...
Your Price
$26.74
In Stock
KitchenAid Washer Drain Hose
I replaced the hose and reinstalled the panels and I was done. Read more...
PartSelect Number PS11747970
Manufacturer Part Number WPW10003250
This hose goes from the drain pump to the back of the washer.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
anthony from EASTPOINTE, MI
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.I replaced the hose and reinstalled the panels and I was done. Read more...
Your Price
$48.56
In Stock
KitchenAid Washer Drain Hose with Clamp
PartSelect Number PS334596
Manufacturer Part Number 285664
Used to drain water.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Steve from Cypress, CA
Leaking drain hose
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Read more...
Your Price
$21.53
In Stock
KitchenAid Washer Inlet Hose - 5 FT
PartSelect Number PS11746820
Manufacturer Part Number WP89503
This hose can handle hot or cold water and is five feet long.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Helen from NASHUA, NH
Your Price
$12.00
In Stock
KitchenAid Washer Water Level Pressure Switch Hose
PartSelect Number PS11747972
Manufacturer Part Number WPW10004260
Fixes these symptoms
- Will not drain
- See more...
Your Price
$26.01
In Stock
KitchenAid Washer Extension Hose
PartSelect Number PS334681
Manufacturer Part Number 285863
This part is used to extend washing machine drain hose approximately 4 feet. You may also require the connector (PartSelect Number PS334663) to connect the extension to the existing drain hose.
Fixes these symptoms
- Leaking
- See more...
Related KitchenAid Washer Parts
- All KitchenAid Washer parts
- KitchenAid Washer Brackets and Flanges
- KitchenAid Washer Caps and Lids
- KitchenAid Washer Dispensers
- KitchenAid Washer Hardware
- KitchenAid Washer Hinges
- KitchenAid Washer Knobs
- KitchenAid Washer Seals and Gaskets
- KitchenAid Washer Springs and Shock Absorbers
- KitchenAid Washer Switches
- KitchenAid Washer Wire Plugs and Connectors
