KitchenAid Washer Dryer Combo Hardware

Videos!

Your Price

$13.42

KitchenAid Washer Dryer Combo Roller Support Tri-Ring

★★★★★

5 Reviews

PartSelect Number PS11755850

Manufacturer Part Number WPW10512946

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

Fixes these symptoms

Noisy
See more...

Installation Instructions

John from Tucson, AZ

worn out part

The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair. Read more...

Videos!

Your Price

$40.54

KitchenAid Washer Dryer Combo Igniter Kit

★★★★★

33 Reviews

PartSelect Number PS334180

Manufacturer Part Number 279311

If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder kit includes the 3-inch flat igniter, bracket, 4-inch wire leads, and the plug. The kit can replace both round and flat igniters and is used for many gas clothes dryers. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is located within the burner assembly, so you will require tools to complete the repair. You will need a putty knife, a small flat blade screwdriver, a 5/16 nut driver, and a 5/16 socket with a ratchet.

Fixes these symptoms

Not Heating
See more...

Installation Instructions

TEODY from MILPITAS, CA

No Heat. Dryer keeps running but no heat to dry clothes.

Repair was very easy. We are in the internet age so I use it all the time to get info on how to repair any thing in the house including cars. This time it was my dryer. I typed up 'Kitchen Aid dryer has not heat'and pressed searched and PartSelect came up. Typed in the model number and looked up the comments on No Heat. They had pretty cool site that shows videos on how to repair this things too. Came to conlclusion that the THERMAL FUSE was the main problem. Ordered it and as well as the Igniter assy just to make sure and as well as save on the shipping just in case. Ordered on Sunday night and the shipped the next day. It arrived on Tuesday. Unfortunately had a little problem on the shipment. Called PartSelect and they are so awesome they shipped me new parts asap at no extra charge. Awesome Awesome! Parts came in Thursday and first installed the Thermal Fuse and BAAAM! problem solved. Did not need the igniter assembly. Now I have an extra part in storage.
To replace the Thermal fuse.
1. Disconnect Dryer from power outlet. Remove the bolts on the back panel with a 1/4" socket. I used power drill because it is much faster.
2. Locate the Thermal Fuse. Disconnect wires and remove the bolt. Slide it up and pull. Install the new one and reconnect the wires. Replace the panel and plug the dryer.

That solved my problem. It should solve yours too. The whole process was less than five minutes. Read more...

Videos!

Your Price

$7.04

KitchenAid Washer Dryer Combo Agitator Bolt

★★★★★

10 Reviews

PartSelect Number PS11741866

Manufacturer Part Number WP358237

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Fixes these symptoms

Leaking
Marks left on clothes
Spins slowly
See more...

Installation Instructions

Dexter from Milwaukie, OR

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose

After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...

Your Price

$16.46

KitchenAid Washer Dryer Combo Single Front Panel Cip

★★★★★

3 Reviews

PartSelect Number PS11731288

Manufacturer Part Number W10854425

This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Sean from BAR NUNN, WY

Belt was slipping, and having a hard time spinning the drum

First off, start by turning of the breaker to the dryer and confirming the power has been turned off. Next, remove the lint screen and two screws holding the lint screen housing to the lid. Remove the two side moldings on the control panel and the two screws holding doun the enclosure. Slide the control enclosure forward and lift up . Take a picture of the wiring for later reference and carefully unplug the wires and set the enclosure aside. Next, remove the two screws holding the rear lid retaining clips. Gently pry up on the front of the lid to realese hold doun clips, swing the lid up and remove it from the rear clips, set the lid aside. Remove the two screws on corners of front cover located near the top, unplug the door switch. Remove the front cover by lifting straight up, set aside. Now remove the belt from the motor by realeasing the tensioner and remove it from the drum. You can now remove the drum through the front. Now is a good time to check the condition of your drum rollers, clean them as needed or replace them. Clean the roller shafts and apply a quality grease. "Clean the roller groove on the drum" this is what makes the drum sound bumpy! Remove the rear seal and replace it as per the instructions that come with the seal. The glue dries quickly, so have the seal fully in place and apply glue to small areas replacing the seal fully before moving on. You can now reinstall the drum being careful not to damage the seal. Place the drum on the rollers, reach inside and work the seal into place. You can now replace the belt and work in reverse with the casings! It took me longer to type these instructions than it did to make this repair! Enjoy your like new machine! Read more...

Your Price

$5.42

KitchenAid Washer Dryer Combo Screw, 8/18 x 3/8

★★★★★

2 Reviews

PartSelect Number PS11746840

Manufacturer Part Number WP90767

This screw is sold individually.

Installation Instructions

Alexander from Lakeland, FL

Broken Dryer Knob

First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...

Your Price

$8.00

KitchenAid Washer Dryer Combo Knob Spring-Clip

★★★★★

2 Reviews

PartSelect Number PS11743754

Manufacturer Part Number WP688805

Also known as the inside sleeve for the knob to be able to properly fit over the shaft of the switch. Sold individually.

Installation Instructions

Susan from UNIVERSITY PL, WA

Timer knob was cracked, missing spring clip and wouldn't set accurate drying time

I ordered the timer knob and read that I also needed the knob spring clip (this part is non-returnable), so I ordered both. Upon arrival I found that the knob spring clip already comes installed inside the shaft of the timer knob. So you don't need to order both. It was the easiest repair I've ever done. Just position timer knob on D-shaped shaft of dryer timer and push until knob clicks into place. Read more...

Your Price

$7.95

KitchenAid Washer Dryer Combo Cover Screw

PartSelect Number PS11740701

Manufacturer Part Number WP308685

Sold individually.

Installation Instructions

Curtis from PALM BAY, FL

Relocating dishwasher into the new kitchen layout

In this case the dishwasher had already been installed for a few years. After removing it, we inspected it and saw it needed a bit of TLC. The transport wheels on the back were missing, making it harder to move around without scratching the tile and some of the original hardware was rusted or broken off. I looked up the parts easily here on PartsSelect using their parts breakdown diagrams and was glad to see what I needed was still available. We had a licensed plumber relocate the hot water line and drain for us to make things a bit easier.
A licensed electrician had also moved the power line over to the new location and left a wire sticking out of the bottom of the wall to hardwire the dishwasher in again. We decided to convert the dishwasher to be able to be plugged into a standard 20amp wall outlet instead. We had already purchased a kit with a nice long cord and strain-relief snap on plastic fitting that snapped onto the metal incoming power box on the bottom front of the dishwasher. Using the supplied wire nuts, etc., we connected the wires and ground wire to the proper wires from the dishwasher and ground lug. We put the dishwasher aside and then went to work on converting the power wire coming out of the bottom of the wall, to a conventional outlet. I am mentioning all this because in our first attempt we unfortunately put the receptacle a bit high off the floor and the new power cord plug end, stuck out and hit the back of the dishwasher so it would not go all the way in and was sticking out from under the counter top. I tried using one of those flat adapter cables, but even that still stuck out to far. So we ended up relocating the outlet box as low as we could on the wall and this allowed the plug to stick out into the opening area at the bottom rear area of the dishwasher so it could now be slid all the way in under the kitchen counter properly. I hope that bit of trial and error will save you some time if you ever decide to go the pluggable route too.
The new installation required the use of the dishwasher side mount brackets, so we had to purchase a replacement set of those, complete with the hardware to screw them down.

This project took a bit longer than planned due to the power plug problem, one which we will remember for any other similar appliance relocation projects, as well as the time to get our new parts in that we had to order, but other than that the rest went smoothly and the dishwasher was relocated successfully. Read more...

Videos!

Your Price

$11.80

KitchenAid Washer Dryer Combo Hose Clamp

★★★★★

1 Review

PartSelect Number PS11743008

Manufacturer Part Number WP596669

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

Fixes these symptoms

Leaking
See more...

Installation Instructions

jeff from lindenhurst, IL

Washing Machine was leaking water

Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years! Read more...

Your Price

$5.36

KitchenAid Washer Dryer Combo Roller Shaft Washer

PartSelect Number PS11741763

Manufacturer Part Number WP348197

Fixes these symptoms

Noisy
See more...

Installation Instructions

Edward from Andover, NJ

Dryer was sqeaking loudly when running

I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan Read more...