This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$7.88
In Stock
Order within the next 1 hr and 47 mins and your part ships today!
This Flat Beater Part Number WPW10672617 is for Stand Mixers. Attaches to the beater shaft and is for normal to heavy mixtures such as cake batters or cookie dough. This has a powder coated finish.
$26.98
In Stock
Order within the next 1 hr and 47 mins and your part ships today!
This wire whip is for stand mixers.
Wire whip attaches to the beater shaft and incorporates air into cream, eggs and frostings.
Follow the instructions in the owner's manual for using and installing this part.
$31.74
In Stock
Order within the next 1 hr and 47 mins and your part ships today!
Order within the next 1 hr and 47 mins and your part ships today!
Questions And Answers for KSM90
Ask our experts a question about this model and we'll get back to you as soon as possible!
11 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lee
February 21, 2020
Will not stay running and sometimes will not even come on. My mom said it was sparking last time she used it....help
For model number KSM90
Hello and thank you for writing.
It certainly sounds like a faulty speed control Lever PS2325454 and/or possibly a faulty motor brush PS11753983 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
When I lift the head to remove the bowl, brown fluid oil leaks out by the stand arm.. it comes down the fixture shaft. What should I do?
For model number KSM90
Hello Fred, thank you for contacting us. We have researched and found that when the grease inside the gearbox of a mixer separates, the liquid part of the grease can leak out of the mixer as an oil. We would recommend replacing the grease, part number PS12583821, inside the gearbox, to solve the problem. We hope this helps!
Will not turn on. Was not turning with any power. Changed brushes and it stopped working completely. Does nothing when turned on.
For model number KSM90
Hello Stephen and thanks for writing.
It certainly sounds like a faulty Lever PS2325454 check for signs of damage and replace it if needed. We hope this helps. Please contact us anytime.
We have used this mixer for a long time without problems. Now the bowl is stuck to the base and we cannot remove it. We have tried to turn it counterclockwise per instructions but we can't get it to move at all.
Do you have any suggestions on how we can get the bowl released from the mixer base? Thank you
For model number KSM90
Hi Andy, thank you for getting in touch. Place a wet, warm towel around the bottom of the bowl for 10 minutes. Re-warm it after 10 minutes, put it on again, and let it sit for another 1-2 minutes. This will rewarm the stainless steel, causing it to expand. After this time, try to wiggle and remove the bowl. Another method is to try applying mineral oil to the bottom of the bowl near the crease where the bowl attaches to the base plate. The mineral oil may lubricate the bowl enough to allow it to come loose. If you do not have mineral oil, use vegetable oil cooking spray instead. If you use vegetable oil, make sure to clean the base plate very thoroughly after the bowl is removed because vegetable oil can become very sticky over time. If neither of these techniques works, you can try wrapping the bowl in a towel and gently tapping the handle with a rubber mallet. We hope this solves your problem!
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Pulled the Knob off of the new Lever then pressed it on the old Lever. I had to order the whole lever because it was the part nearest the knob in the illustrated parts break-down. I RECOMMEND THAT THE KNOB BE ADDED TO THE ILLUSTRATED PARTS BREAK-DOWN.
My girlfriends' stand mixer failed when the accessory drive cap fell into the mixing bowl and jambed the beater, spliting the worm gear. The teeth on this gear are made of nylon and are molded to an aluminum center. This part is designed to fail in situations like this, saving the more expensive transmission parts. Following a repair manu
... Read moreal I found online, I first removed the rear cover and pulled out the cord strain relief out from the base. Next I removed the drip cup from around the base of the planetary drive. I then used a pin punch to drive out the pin holding the planetary to the center shaft and removed the planetary. The unit was then inverted and I removed 4 screws holding the bottom cover to the gear case, and the 5 screws from around the planetary drive. The bottom cover was then lifted off. Three screws holding the worm gear bracket in place were then removed and the worm gear assembly lifted out. A small pin holds the worm gear to the shaft. I drove this out with a small pin punch and the shaft and worm gear were then removed. There is also a thrust washer on this shaft, and it's location is important. Make a note for re-assembly. The new gear was installed and the entire process reversed for re-assembly. A successful repair completed! My girlfriend would have replaced this $200 appliance, but I was able to repair it for less than $30 including shipping.
I removed screws in a sequence that I felt wouldn't further damage the mixer until I had it completely unassembled. When I found the broken worm gear, I went online to find a part. I found an exploded view, but the part numbering was old, and the salesperson couldn't tell me what the worm gear and bracket assembly consisted of, as I only
... Read morewanted the worm gear. After trying to drive the pin out of the assembly, and failing, I decided to back online and see if anyone else had a photo of the assembly. Luckily (and wisely) PartSelect,com did and that answered any questions I had. The price was better, too. Reassembly of the mixer was a cinch with the exploded view. It's working like new, and we're hoping for another 35 years of service from it! Thanks.