Washer Dryer Combo Valves
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Washer Dryer Combo Valves
Your Price
$30.89
In Stock
Washer Dryer Combo M Series New Style Coil Kit
2. Removed two bolts at bottom front of machine and took off the bottom front panel.
3. Removed three bolts from black plastic exit vent and took it out to give more room to access everything.
4. removed two wires and screws on the limit thermostat. Did the reverse to place the new one.
5. Removed wires (remembering placement), then holder screw. rotated the Gas Dryer Sensor counter clockwise to release the bottom tab so the sensor can be taken off the flame tube. Did the reverse to place the new one on.
6. Removed the one screw on the gas/flame tube that holds the bracket and igniter inside the flame tube. Removed the wires fro the igniter (remember placement) Slid the whole assembly toward the back of the machine to get the tube off the gas valve then rotated the whole assembly counter-clocwise to release the tab on the left side of the bracket. This was a little tight and had to work with it a bit to get the tab out and slide the whole piece out of the flame tube.
7. Once the tube and igniter were out i removed the scree that holds the igniter and replaced with the new one. Made sure no dust, etc. was in the piece.
8. Did the reverse to place the tube/igniter back into the flame tube.
9. Carefully and forcefully removed the wire connectors to the two coils. These were tough to get off. Removed the two screws that hold the bracket that holds the two coils in place. Slid the coils off the spindles remembering which one has the two wire connection and which one has the three wire connection and the way they went on. Replaced the old with the new. Placed the bracket onto the new coils and made sure the little bumps on the top are in the holes in the bracket. Tightened the screws to hold the coil bracket. Reattached the wire connectors to the coils making sure they go ALL the way back on.
10. Vaccumed everything I could to get lint, dust, etc. out.
11.Replaced the black vent plastic.
12 Made sure the exit vent on the back was not crimped or clogged. Checked the little flap door where the vent goes outside to make sure it opens and closes super easy to no air flow is restricted.
13. For testing I left the bottom panel open. Make sure you closed the door, reconnect the plug and turn the gas valve back on. Hit the go button on autodry or timed dry. The door must be closed to create the closed circulation of the system so the fan sucks the flame into the tube otherwise the flame will not fire deep into the tube and will set off one fo the overheat sensors. After hitting the go button your drum will start to rotate, then a few seconds later you'll hear a click and your igniter will start to burn bright orange. Another click and the gas should flow and ignite.
14. This shows that you've fixed the ignition problem. I just replaced everything I thought that could be wrong in stead of hunting and trial and error. All the parts were about $137 so I thought it was worth making sure.
15. IMPORTANT: If during your test the flame turns off after a little while then turns back on only to turn off again, don't panic. This happened to me as well. I found that you need to run the dryer with wet clothes in the dryer. The wetness in the clothes will keep the autodry sensor from shutting off the dryer since there will be moisture in the exhaust. If it's on timed dry the wet clothes will cool the exhaust air and keep the overheat sensors from turning the heat off. So no heating of dry clothes to get out wrinkles. Just dry the wet clothes. This is all I did and it's been working great so far. Good Luck! Read more...
PartSelect Number PS334310
Manufacturer Part Number 279834
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. The coils are attached to the dryer gas valve. If the dryer does not heat or heats intermittently, the coil may not be opening the gas valve. Both coils must be operational for the valve to open. No continuity would indicate a defective coil, but they can be intermittent and fail when they get hot. Both coils should be replaced when one of them is broken. This part can break as a result of material fatigue from normal use. This part measures approximately 1 inch in diameter and 1 inch in height, and is constructed of plastic and metal. It comes in black/beige. This part features a 3-terminal boost/hold coil and a 2-terminal secondary coil
Fixes these symptoms
- Noisy
- Not Heating
- See more...
Installation Instructions
Michael from Kirkwood, MO
Gas Dryer would not ignite
1. Removed lint screen and holder frame. Unplugged the electrical cord and closed the gas valve in the line before it goes into the dryer.2. Removed two bolts at bottom front of machine and took off the bottom front panel.
3. Removed three bolts from black plastic exit vent and took it out to give more room to access everything.
4. removed two wires and screws on the limit thermostat. Did the reverse to place the new one.
5. Removed wires (remembering placement), then holder screw. rotated the Gas Dryer Sensor counter clockwise to release the bottom tab so the sensor can be taken off the flame tube. Did the reverse to place the new one on.
6. Removed the one screw on the gas/flame tube that holds the bracket and igniter inside the flame tube. Removed the wires fro the igniter (remember placement) Slid the whole assembly toward the back of the machine to get the tube off the gas valve then rotated the whole assembly counter-clocwise to release the tab on the left side of the bracket. This was a little tight and had to work with it a bit to get the tab out and slide the whole piece out of the flame tube.
7. Once the tube and igniter were out i removed the scree that holds the igniter and replaced with the new one. Made sure no dust, etc. was in the piece.
8. Did the reverse to place the tube/igniter back into the flame tube.
9. Carefully and forcefully removed the wire connectors to the two coils. These were tough to get off. Removed the two screws that hold the bracket that holds the two coils in place. Slid the coils off the spindles remembering which one has the two wire connection and which one has the three wire connection and the way they went on. Replaced the old with the new. Placed the bracket onto the new coils and made sure the little bumps on the top are in the holes in the bracket. Tightened the screws to hold the coil bracket. Reattached the wire connectors to the coils making sure they go ALL the way back on.
10. Vaccumed everything I could to get lint, dust, etc. out.
11.Replaced the black vent plastic.
12 Made sure the exit vent on the back was not crimped or clogged. Checked the little flap door where the vent goes outside to make sure it opens and closes super easy to no air flow is restricted.
13. For testing I left the bottom panel open. Make sure you closed the door, reconnect the plug and turn the gas valve back on. Hit the go button on autodry or timed dry. The door must be closed to create the closed circulation of the system so the fan sucks the flame into the tube otherwise the flame will not fire deep into the tube and will set off one fo the overheat sensors. After hitting the go button your drum will start to rotate, then a few seconds later you'll hear a click and your igniter will start to burn bright orange. Another click and the gas should flow and ignite.
14. This shows that you've fixed the ignition problem. I just replaced everything I thought that could be wrong in stead of hunting and trial and error. All the parts were about $137 so I thought it was worth making sure.
15. IMPORTANT: If during your test the flame turns off after a little while then turns back on only to turn off again, don't panic. This happened to me as well. I found that you need to run the dryer with wet clothes in the dryer. The wetness in the clothes will keep the autodry sensor from shutting off the dryer since there will be moisture in the exhaust. If it's on timed dry the wet clothes will cool the exhaust air and keep the overheat sensors from turning the heat off. So no heating of dry clothes to get out wrinkles. Just dry the wet clothes. This is all I did and it's been working great so far. Good Luck! Read more...
Your Price
$26.80
In Stock
Washer Dryer Combo Water Inlet Valve - Hot
PartSelect Number PS3527427
Manufacturer Part Number 5220FR2006H
The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Khanh from CHICAGO, IL
Water continued to fill into the drum slowly after the load was done.
Watched a you tube video and followed the instructions. Even had my 11 and 13 yo old help and do most of the work. Very easy to fix both hot and cold inlet at the same time. Didn't know which one was causing the problem so I decided to replace both.
Read more...
Your Price
$35.28
In Stock
Washer Dryer Combo Water Inlet Valve with Mounting Bracket
compoments and reassembled.
Test run machine. Ran like new! Read more...
PartSelect Number PS334646
Manufacturer Part Number 285805
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Don from Wyoming, MN
Washer stopped at rinse cycle
Removed the top and back panels. Replacedcompoments and reassembled.
Test run machine. Ran like new! Read more...
Your Price
$72.90
In Stock
Washer Dryer Combo Water Inlet Valve - Cold
PartSelect Number PS11728995
Manufacturer Part Number 5220FR2075L
The cold water inlet valve on your washing machine dispenses the cold water and bleach into the washer in the prewash cycle. This inlet valve has a standard hose fitting inlet and 2 water outlets facing 45 degrees to the left. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 4 inches long x 3 inches wide.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
John from Northport, NY
Inlet valve leak
Followed directions on the video and went like a charm. Very impressed with service and video
Read more...
Your Price
$127.65
In Stock
Washer Dryer Combo Water Inlet Valve
PartSelect Number PS815509
Manufacturer Part Number 134190200
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.
Fixes these symptoms
- Leaking
- No hot or cold water
- See more...
Installation Instructions
alvaro from east hampton, NY
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read more...
Your Price
$21.45
In Stock
Washer Dryer Combo M Series Ignition Coil Kit
PartSelect Number PS470049
Manufacturer Part Number 5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, the gas valve coils can be defective and replacing this part will help. Customers rate this project as easy. Refer to the installation diagram for further instructions. For safety, unplug your dryer before repair.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Brett from Monticello, MN
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
Read more...
Your Price
$98.44
In Stock
Washer Dryer Combo Water Inlet Valve
PartSelect Number PS1583805
Manufacturer Part Number 205613
This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. The tools needed for this repair are: a 5/16 nut driver, 1/4 nut driver, and a small flat blade screwdriver. If cold water does not flow into washer, or the washing machine will not fill with hot water, replacing the valve can be the solution. To gain access to the water valve, locate the back of the washer and remove the hot and cold hoses, as well as the whole assembly. Next, remove the four wires and loosen up the clamp. After removing the old valve, replace it with the new one and reconnect the wires and hose. Remember to disconnect the washer from the power source before starting this project.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Brian from El Cajon, CA
Cold water valve only opened to a trickle
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off the outlet hose. I reversed the steps to install the new assembly and the total repair took about 10 minutes.
Read more...
Your Price
$126.23
In Stock
Washer Dryer Combo Washer Water Inlet Valve
PartSelect Number PS12374721
Manufacturer Part Number AJU75152601
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
Fixes these symptoms
- Leaking
- No hot or cold water
- Water Filling Issues
- See more...
Installation Instructions
Flora from MIAMI, FL
Water continued leaking into washer after the end of cycle through the water inlet valve.
Did the repair Myself. Saved $ 400.00 in the process.
Read more...
Your Price
$108.19
In Stock
Washer Dryer Combo Inlet Valve Assembly
PartSelect Number PS3527452
Manufacturer Part Number 5221ER1003A
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Keineth from DALLAS, TX
Your Price
$118.84
In Stock
Washer Dryer Combo Dual Cold Water Valve
PartSelect Number PS11750469
Manufacturer Part Number WPW10212596
Water inlet valve controls the water flow into the washer.
Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW and YNFW; and Inglis IFW and YIFW.
Also fits some laundry centers in these series: Whirlpool CET and CGT; and Maytag MLE and MLG.
Fixes these symptoms
- Does not dispense fabric softener or detergent
- Leaking
- No hot or cold water
- See more...
Installation Instructions
Laura from ENGLEWOOD, CO
Washer would fill extremely slowly when on cold water wash resulting in long fill(LF) error code.
The washing machine would only run on the hot water cycle. When trying to use the warm or cold setting, the water would dribble into the drum and result in an LF error code(long fill). I watched a brief video on replacing the water inlet valve which made it really easy to repair. I first turned off the water, disconnected the hoses from the machine, and opened the top to access the valves. I then disconnected the wires from the valve, removed the water tubes, swapped out the valves and put everything back together. I am not experienced in repair but this was a very easy fix! We decided to replace the single hot water valve and the dual cold water valve since it's an older machine and it works like new again!
Read more...
