Washer Dryer Combo Handles
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Washer Dryer Combo Handles
Your Price
$16.76
In Stock
Washer Dryer Combo Door Handle
PartSelect Number PS11743752
Manufacturer Part Number WP686711
White in color.
Your Price
$71.00
In Stock
Washer Dryer Combo Handle
PartSelect Number PS11752787
Manufacturer Part Number WPW10321839
Fixes these symptoms
- Door latch failure
- See more...
Your Price
$63.94
In Stock
Washer Dryer Combo Handle
PartSelect Number PS626972
Manufacturer Part Number 131789400
This handle is used on washer/dryer combos.
Your Price
$55.86
In Stock
Washer Dryer Combo Door Handle
I thought the problem would turn out to be the motor, but instead it was the front seal for the drum. It is felt and had broken. It folded under itself and was jamming the drum to the point that the motor couldn't turn it.
I replaced the felt seal, which attaches to the front cover with three clips and also replaced the plastic guides, which clip to the drum. Both were easy to do. I had replaced the rear drum seal a few years ago and so it was ok, otherwise I would recommend doing that too.
While I had it apart, I opened up the back and cleaned out all the lint in the fan housing. I had replaced the heater element, thermal switch and fuse a few years ago, so they were fine.
I also replaced the mosture sensor, just because it only cost $11. I bought a new lint filter, because it had holes in it after 20 years. I replaced the belt, because it was only $10. I replaced the lint filter cover and front door handle, because they had yellowed. I will warn you about the front door handle. It was a bear. I finally had to take the door apart to get the little plastic clip to seat correctly.
Then I put it all back together, which again is easier with 3 hands. Holding up the drum and putting the front cover on the lower clips can be a bit tricky alone. Also, be sure to rotate the drum to make sure the rear seal is not folded under and the front seal is seated correclty.
I fired it up and it ran great, except for the constant whistling. I had wondered what the little clear plastic box in the back did. Turns out it is the lint filter is full whistle warning thing. I took the back off again and found a wire was resting on the flapper door of the box and holding it in the wrong postion. By the way, it is a really irritating sound after the first few minutes. I moved the wire and it works great.
I worked slowly and it went well and was not hard. Read more...
PartSelect Number PS11741770
Manufacturer Part Number WP348721
White in color.
Installation Instructions
Chris from Worcester, MA
Motor tried, but could not turn drum
First, I unplugged it and pulled it away from the wall. Then I pryed the front of the top up. It is scary to apply that much force, but the clips did not break. It opens like a car hood. Then I removed the two sheet metal screws that hold the front to the sides. Don't forget to unplug and unclip the door switch wires. Then I lifted the front off the bottom clips. Be sure to hold the drum up when you do this. Three hands will make it easier. Then remove the drum and belt. The belt tensioner will fall off, but that is ok. I thought the problem would turn out to be the motor, but instead it was the front seal for the drum. It is felt and had broken. It folded under itself and was jamming the drum to the point that the motor couldn't turn it.
I replaced the felt seal, which attaches to the front cover with three clips and also replaced the plastic guides, which clip to the drum. Both were easy to do. I had replaced the rear drum seal a few years ago and so it was ok, otherwise I would recommend doing that too.
While I had it apart, I opened up the back and cleaned out all the lint in the fan housing. I had replaced the heater element, thermal switch and fuse a few years ago, so they were fine.
I also replaced the mosture sensor, just because it only cost $11. I bought a new lint filter, because it had holes in it after 20 years. I replaced the belt, because it was only $10. I replaced the lint filter cover and front door handle, because they had yellowed. I will warn you about the front door handle. It was a bear. I finally had to take the door apart to get the little plastic clip to seat correctly.
Then I put it all back together, which again is easier with 3 hands. Holding up the drum and putting the front cover on the lower clips can be a bit tricky alone. Also, be sure to rotate the drum to make sure the rear seal is not folded under and the front seal is seated correclty.
I fired it up and it ran great, except for the constant whistling. I had wondered what the little clear plastic box in the back did. Turns out it is the lint filter is full whistle warning thing. I took the back off again and found a wire was resting on the flapper door of the box and holding it in the wrong postion. By the way, it is a really irritating sound after the first few minutes. I moved the wire and it works great.
I worked slowly and it went well and was not hard. Read more...
Your Price
$19.55
In Stock
Your Price
$17.27
On Order
Washer Dryer Combo Handle
PartSelect Number PS3535330
Manufacturer Part Number MEB61281101
Installation Instructions
Jeff from LOS ANGELES, CA
Broken Handle
Removed the door by undoing two hex nuts. Then removed the plastic cover over the glass and attached to the metal door frame. Broken part easily came out. But putting back together took two phone calls to you and finally getting the video from you that showed that the tension on the door spring was induced by the attachment of the outer plastic piece. The the spring worked as it should and I could easily return the door to it's place on the machine. I now know how to fix this when it breaks the next time.
Read more...
Your Price
$42.19
In Stock
Your Price
$75.30
Special Order
Your Price
$50.46
Special Order
Washer Dryer Combo Door Handle - White
PartSelect Number PS11741461
Manufacturer Part Number WP3392906
Screws NOT included.
Your Price
$8.28
Special Order
