Shindaiwa Power Broom Parts

Shop By Appliance Type Shop By Part Type

Popular Shindaiwa Power Broom Parts

Your Price

$4.99

Shindaiwa Power Broom Primer Pump

PartSelect Number PS8858167

Manufacturer Part Number 12318140630

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs onto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

Your Price

$8.60

Shindaiwa Power Broom Filter, Fuel

★★★★★

2 Reviews

PartSelect Number PS11826309

Manufacturer Part Number A369000460

The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy. The part attaches inside of the fuel tank and is used to clean the fuel of debris. It should be changed regularly. Check your owners manual for the recommended replacement schedule for your engine. If the fuel is leaking or their is a blockage, you will know the part is broken and will likely need to be replaced. To check for small leaks, feel around for dampness and the smell of fuel.

Installation Instructions

Keith from NORWOOD, NJ

Replace clogged fuel filter.

Thru fuel cap, insert copper wire with hook formed on end. Fish around until you grab the fuel line. Pull the fuel line and filter thru the fuel fill neck.
Pull off old filter and replace with new. Push back into fuel tank & be done. Read more...

Your Price

$6.82

Shindaiwa Power Broom Fuel Filter

PartSelect Number PS11836543

Manufacturer Part Number A369000440

This OEM Fuel Filter is a white and silver, steel part, sold individually. It requires a pair of pliers to install and is ranked as Easy to repair by our customers. This part attaches inside of the fuel tank, and is used to clean the fuel of debris. This part should be changed regularly as part of good engine maintenance. If the engine sounds like it is not getting enough fuel or is underperforming, remove the filter to heck for a blockage. If there is a blockage or the part is leaking, then it likely needs a replacement.

Your Price

$5.19

Shindaiwa Power Broom Gasket

PartSelect Number PS9237390

Manufacturer Part Number V107000010

This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. This gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

Bolt, TORX 5x20 – Part Number: V855000000

Your Price

$3.99

Shindaiwa Power Broom Bolt, TORX 5x20

PartSelect Number PS9235848

Manufacturer Part Number V855000000

Your Price

$19.06

Shindaiwa Power Broom Front Handle

PartSelect Number PS10043289

Manufacturer Part Number C040000450

Pre-Filter, Foam – Part Number: A226000700

Your Price

$4.99

Shindaiwa Power Broom Pre-Filter, Foam

PartSelect Number PS9313973

Manufacturer Part Number A226000700

This Foam Air Filter is a yellow, foam part, used to filter out contaminents from entering the engine. It lays on top of the main air filter, is rated as "Easy" to install, and requires a screw driver . If your filter is dirty and discolored then it has worn out, and the part should be replaced. Refer to your make, model and diagram to ensure this air filter is correct for your machine.

Your Price

$4.99

Shindaiwa Power Broom Nut 5

PartSelect Number PS9148697

Manufacturer Part Number 90050000005

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have various uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.