Pole Saw Carburetors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Pole Saw Carburetors
Your Price
$6.21
In Stock
Pole Saw Bulb-Purge "snap-in"
Instead of running the line into the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through. Read more...
PartSelect Number PS9471212
Manufacturer Part Number 530047721
This primer bulb, also known as a purge bulb, is used to push more fuel from the fuel tank into the carburetor of your small engine equipment, to help the engine start easier. Over time and through extended use and exposure to gas and oil, the bulb of the primer will eventually lose its elasticity and crack or break. This bulb is made of plastic and can be replaced by accessing the ignition system. Disconnect the fuel lines and pop out the bulb with a set of pliers, and once you pop in the new bulb, you just reconnect the fuel lines. This bulb is compatible with a variety of makes and models of small engine equipment and is sold as an individual part.
Installation Instructions
Robert from MANVILLE, NJ
Replace the fuel lines
Replaced all fuel lines. Followed instructions found on Partselect.com, which said to insert cut fuel line in tank and use forceps to reach back in the tank and pull the fuel line through. The problem was that I did not have forceps, or needle nosed pliers that could reach the end of the hose. Instead of running the line into the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through. Read more...
Your Price
$68.89
In Stock
Pole Saw Carburetor
PartSelect Number PS10039121
Manufacturer Part Number A021001692
This is a genuine OEM replacement part, it is sold individually. It is used on a variety of Echo Gas Powered Equipment. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem.
Rb-K93
Your Price
$38.60
In Stock
Pole Saw Carburetor
PartSelect Number PS11824881
Manufacturer Part Number 588171156
This OEM carburetor mixes the air-fuel mixture to the proper ratio for combustion in your engine. This carburetor is sold individually, is silver in color and metal in material, and is located on the intake of the engine.
Issues with your carburetor will cause problems with your engine running, and could cause excessive smoke due to too much gas. This can happen due to corrosion inside the carburetor. Carburetors can be rebuilt easily, and repairing them requires an allen wrench and a screwdriver. When troubleshooting your carb, remove the air filter and pour a teaspoon of fuel into the carburetor. Pull the starter rope, and if the engine starts then quickly dies, the carburetor is likely the problem.
When replacing your carburetor, also replace all gaskets when doing so, as they are a one-time use.
Your Price
$32.49
Special Order
Pole Saw Carburetor Assembly
PartSelect Number PS9937863
Manufacturer Part Number 308054013
This carburetor assembly in your lawn equipment mixes air and fuel to create a combustible mixture for the engine. A broken carburetor assembly can cause engine issues like running too lean or too rich, sputtering, stalling, fuel leaks, or a strong fuel odor. It is crucial to replace a faulty carburetor assembly promptly to avoid safety hazards from fuel leaks and prevent engine failure due to fuel flooding. Replacing the carburetor requires a socket set. To replace the carburetor, use a socket set to remove the screws on the air filter base and disconnect the fuel lines before lifting it out of your machine. This OEM-verified assembly is sold separately from its fasteners.
Your Price
$5.61
In Stock
Your Price
$81.56
In Stock
Pole Saw Carburetor
PartSelect Number PS10039106
Manufacturer Part Number A021000723
This is an Original Manufacturer Approved Carburetor Assembly used on a variety of Gas Powered String Trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won\\\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem.
Rb-K70A
Your Price
$12.94
In Stock
Your Price
$93.90
In Stock
Your Price
$48.56
In Stock
Your Price
$10.05
On Order
