Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
Models
>
MVWB450WQ1
MVWB450WQ1 Maytag Washer - Overview
Sections of the MVWB450WQ1
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Drain Pump
PartSelect #: PS5136124
Manufacturer #: W10536347
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$136.28
In Stock
Basket Hub Kit
PartSelect #: PS11723155
Manufacturer #: W10820039
This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
$37.80
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Lid Lock Assembly
PartSelect #: PS11756782
Manufacturer #: WPW10619844
This part makes sure that the lid is shut before allowing the machine to start or agitate.
NOTE: This is a manufacturer substitution. Part may differ in appearance but is a functional equivalent to prior parts including
$95.14
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.02
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.12
In Stock
Lid Hinge Mounting Screw
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$11.80
In Stock
Hinge
PartSelect #: PS11746532
Manufacturer #: WP8563964
This is a replacement lid hinge for your washer. It is approximately 2.5 inches in length and 1.5 inches in width. The lid hinge is what the lid for your washer pivots on. If the lid hinge is damaged,...
$8.02
In Stock
Screw, 8-16 x 1.000
PartSelect #: PS11746167
Manufacturer #: WP8533953
Sold individually.
$7.97
In Stock
Sensor
PartSelect #: PS11749664
Manufacturer #: WPW10178988
This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To c...
$44.03
In Stock
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$21.57
In Stock
Spray Paint - 12 oz. - White
PartSelect #: PS347819
Manufacturer #: 350930
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Questions And Answers for MVWB450WQ1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Veronica
January 14, 2020
What does "ld" mean? The machine is blinking this message and beeping. Also, washer is making a humming noise, but won't start.
For model number MVWB450WQ1
Hello Veronica and thank you for writing.
Error codes flash on the control panel to indicate possible clogs in the pumps. "Ld" or "C8" error codes indicate a slow or stopped drain pump, and "C6" indicates that the recirculation pump has stopped. Remove the pumps to access and remove the items clogging them. We hope this helps. Please contact us anytime if you require further assistance.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Simon
July 20, 2021
I had 2 code of malfonction. Ld and sd. And when the draining pump have to start. I here a lot of noise like knocking. But when started ,seem to drain well. But the codes are still there . Dont want to rinse and drain without stop and restart the machine. Do you think its the drain pump?
For model number MVWB450WQ1
Hi Simon,
Thank you for your question. The LD error code is letting you know that the drain pump has either stopped, is not working or it is clogged. The SD error code means that there are too many suds in the washer. If you are hearing a loud knocking, you may have a bad bearing or it could be coming from the drain pump. If it is the bearing that is causing the noise, the outer tub would have to be replaced. The tub has been discontinued and for information on a replacement you would need to contact the manufacturer. We hope this helps! Good luck with the repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Margaret
May 24, 2022
Does anyone know the cubic foot capacity of this machine?
For model number MVWB450WQ1
Hello Margaret, Thank you for the question. This model shows to be 4 Cu. Ft. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jim
February 2, 2020
There is a puddle of water under washer after each load. When tipped on its front, you can hear water swishing around when your turn the agitator (metal circle) in the center of the bottom. Pumps appear dry and hoses or in tact but water is leaking from somewhere. Any ideas of what to look for
For model number MVWB450WQ1
Hi Jim, thank you for your question. The part that we would recommend checking would be your outer tub and the seal in that inner tub. It sounds like either your seal has gone and needs to be replaced, or the tub has cracked and is causing the leak. However you may also just want to double check that all of the tubes are connected securely in place. Just to make sure it is not a simple part that is the problem. Good luck with you repair.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the MVWB450WQ1
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loose change entered drain pump, cracked housing leaked all water out
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.
Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover ... Read more over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.
At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).
Re-assemble using new pump.
Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover ... Read more over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.
At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).
Re-assemble using new pump.
Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
Read less
Parts Used:
-
ROBERT from BARRINGTON, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
204 of 237 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was noisy, Top seal and bearing bad
You better be confident in your repair abilities before you try this. Get the washer to a large open area, like your garage, because there are a lot of parts. Take off the back, pop the top, unsnap and remove the top ring off outer tub, take out the agitator, take out the inner tub, disconnect the pumps and electrical wires, take screw ou
... Read more
t of rotor on bottom and remove rotor, take out 4 bolts to remove motor magnet ring, and now you may be ready to unhook the outer tub from the 4 supports (springs) and lift it out of the metal frame. Then unscrew the bottom nut on the shaft, use blocks to hold the tub in place, and carefully tap the old shaft and bearings out. The instructions that came with the kit helped. The shaft and top seal comes out the top first. Then you can tap out upper bearing and then the lower bearing and spacers.Instructions called for a special tool to install the bearings but you can carefully tap them in. You will need blocks to support the tub while you tap them. First block under the tub and install top bearing, then flip over and use several blocks to hold tub while you drop the shaft, spacers, and tap lower bearing in. I did not need to tap on the inner ring of the bearings, just the outer ring. Be very careful not to damage the seal in the bearings. That's why you must tap them in careful and slow. Them install the nut on the bottom. You need to hold the shaft with damaging it while you tighten the nut. I used the hard nylon gear from the inner tub which I was replacing with a new one. Then put it all back together.
Read less
Parts Used:
-
DENNIS from OELWEIN, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
151 of 163 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water pump for draining
The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring cla
... Read more
mps, unhooked the wiring( its a single plug in) and reverse the procedure for installing.
I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.
I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.
I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.
I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.
Read less
Parts Used:
-
Kerry from Alleyton, tX, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set
67 of 80 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!