Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
Models
>
MAH9700AWW
MAH9700AWW Maytag Washer - Overview
Sections of the MAH9700AWW
[Viewing 6 of 6]Manuals & Care Guides for MAH9700AWW
Click to downloadKeep searches simple, eg. "belt" or "pump".
Door Lock Latch
PartSelect #: PS11745016
Manufacturer #: WP8182634
This part is used on front load washers and includes the interlock switch assembly.
$123.33
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Door Lever
PartSelect #: PS11741552
Manufacturer #: WP34001260
Also known as a door strike.
$68.59
In Stock
Drain Pump - 120V 60Hz
PartSelect #: PS11741568
Manufacturer #: WP34001340
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
NOTE: Pump only, mounting bracket is NOT included.
$164.55
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.12
In Stock
Leveling Leg with Rubber Foot
PartSelect #: PS2037271
Manufacturer #: 34001341
Sold individually.
No Longer Available
Shock Damper - Rear
PartSelect #: PS11741561
Manufacturer #: WP34001292
This part helps keep the washer from vigorous shaking during its cycles. They are sold individually. They mount to the rear half of the outer tub. Appliance would take 2.
$94.07
In Stock
Shock Damper - Front
PartSelect #: PS11741563
Manufacturer #: WP34001303
This part helps keep the washer from vigorous shaking during its cycles. They are sold individually. They mount to the front half of the outer tub. Appliance would take 2.
$95.33
In Stock
Hot Water Valve
PartSelect #: PS11741538
Manufacturer #: WP34001131
This part is the replacement hot water valve for your washer. It is approximately 2-1/2 inches by 3-1/2 inches, and the valve head is approximately 1 inch in diameter. The hot water inlet valve in yo...
$127.11
In Stock
Questions And Answers for MAH9700AWW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pravin
June 30, 2021
Parts for Maytag washer bearing and drum
For model number MAH9700AWW
Hello Pravin, Thank you for contacting us. We have researched the model you have provided and have found the Bearing was only sold as part of the Rear Tub Assembly. The Rear Tub is listed as No Longer Available/Discontinued sorry. There are no part substitutions listed. Our suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers and contact us back with he updated substitution number. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Mario
February 23, 2020
Washer has no power lights on power coming in is good machine will not turn on
For model number MAH9700AWW
Hello Mario, thank you for your question. If the lights are on on the display panel but the unit will not start, we would recommend testing the Door Lock Latch Part Number: PS11745016, and both water valves PartSelect Number: PS11741549 and PartSelect Number: PS11741538 and the Pressure Sensor PartSelect Number: PS11741566. If those parts are tested and are fine, the issue could be with one of the control boards or sensor control board PartSelect Number: PS11741583. I hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the MAH9700AWW
[Viewing 7 of 7]Lid or door won’t close
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to ... Read more p opening.
7. reverse order to finish.
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to ... Read more p opening.
7. reverse order to finish.
Read less
Parts Used:
-
James from Vilonia, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
192 of 231 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Coins had been pulled into the pump, breaking blades and cracked casing.
First I unplugged the washer and removed the back cover plate of the washer. I drained the pump and drainage lines. I then removed the two hose clamps and removed the connecting hoses. I removed the electrical connection. I loosened the three mounting bolts holding the mounting plate holding the pump. Once out, I could remove the pum
... Read more
p from the plate and replaced it with the new part. I remounted the mounting plate, attached the hoses and clamps. I reattached the electrical connection and the back plate to the washer.
The Maytag is well designed and the parts are easy to reach. At least from this experience, the machine was designed with efficient repairs in mind. This is a sign of a well made machine.
The Maytag is well designed and the parts are easy to reach. At least from this experience, the machine was designed with efficient repairs in mind. This is a sign of a well made machine.
Read less
Parts Used:
-
Robert from El Paso, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set, Wrench set
144 of 161 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door lock was in the locked position and door could not close
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the bac ... Read more k of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the bac ... Read more k of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Read less
Parts Used:
-
Suryakant from Cortlandt Manor, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
65 of 71 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!