Parts That Fix KitchenAid Dishwasher KUDS03FTSS3 Not cleaning dishes properly

Also known as the water supply tube.

Supplies water from the main water feed tube to the middle manifold water tube.

The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle. Before you begin this repair, it is recommended that you pull your dishwasher out of the cabinet, so you can tip the dishwasher to one side and gain better access to the circulation pump and motor. Be sure to disconnect the power source and the water source to the dishwasher before you begin this repair. To complete this repair you will need a 1/4 inch nut driver and a 3/8 inch nut driver.

Measures level of soil in the water.

Water is supplied to the lower spray arm via the pump assembly.

This part is essential in your dishes getting clean during the wash cycle. If there is any debris or a tear in the filter, it can cause extra buildup and, therefore, causing dirty dishes.

Also known as a water supply tube which is used for your middle spray arm.

This silverware basket holds utensils in your dishwasher. If it becomes damaged or goes missing, you can replace it with this part. No disassembly is required to replace this part; simply remove the existing basket and replace it with the new one. To keep the basket in good shape, place silverware carefully inside, and be careful when removing and replacing the basket when unloading utensils.

Turbo zone manifold.

This part moves water up from the sump collection area and up through the spray arms.

The spray arm in your dishwasher spins and sprays the water that is used to clean your dishes. If the spray arm is damaged, your dishwasher will not clean properly, and you will need to replace it. Many of our customers have rated this repair as easy, and to complete the repair you will simply need to unscrew the old arm, and replace it with a new one. Make sure the jets are facing upward when you secure the new arm. This part is made of gray plastic and is approximately 18 inches wide.

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.

This part is used to cover the chopper blades.

This part releases the detergent and rinse aid into the dishwasher. Light grey in color. The detergent dispenser attaches to the inner door panel and holds the dishwasher detergent and rinse agent in a covered compartment.

This dishwasher heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.

This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.

The lower spray arm hub sits inside the dishwasher at the base, and feeds water into the lower spray arm. The arm hub is made of plastic and measures 3 inches long by 1.5 inches wide. If the spray arm becomes loose, or does not spin freely, check for damage to the spray arm hub. This is a genuine OEM replacement part sourced directly from the manufacturer.

This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the dishrack. If your clip is cracked or damaged, it is best to replace this part. To repair, first lift the release tab and hold the other side to prevent it from falling off. After lifting it off, you can set the new clip on the tine row and lock it up. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to wear work gloves as a safety precaution. This repair was rated as very easy by our customers and should be done in 15 minutes or less.

This drain hose is 6 and 1/2 feet.

This board is located in the control panel of the dishwasher.Thermal fuse is NOT included.

This part is the replacement upper spray arm retainer or mount for your dishwasher. It is made of gray plastic and is approximately 4 inches by 3 inches. The upper spray arm mount attaches the spray arm to the water supply manifold. If the mount is loose damaged, you may notice that the spray arm wobbles, or possibly hangs from the top of the dishwasher. If this is the case, the mount may need to be replaced. If your dishes are not being cleaned properly, you may want to inspect the mount to ensure that it is not loose, disconnected, or damaged. This part is sold individually and is an authentic OEM part.

This part is used to drain water from your dishwasher.

This part forces the water from the pump to the sump area for discharge.