Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
Models
>
KUDC10FXSS7
KUDC10FXSS7 KitchenAid Dishwasher - Overview
Sections of the KUDC10FXSS7
[Viewing 13 of 13]Keep searches simple, eg. "belt" or "pump".
Lower Dishrack Wheel
PartSelect #: PS3406971
Manufacturer #: W10195416
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
$46.13
In Stock
Door Balance Link Kit
PartSelect #: PS972325
Manufacturer #: 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$33.18
In Stock
Rack Stop Clip
PartSelect #: PS11750071
Manufacturer #: WPW10195622
This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and fal...
$8.12
In Stock
Mounting Bracket
PartSelect #: PS11745496
Manufacturer #: WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$10.06
In Stock
Chopper Assembly
PartSelect #: PS1734917
Manufacturer #: W10083957
This chopper assembly chops up/mince the food particles to prevent from clogging the dishwasher pump.
$34.84
In Stock
Drawer Track
PartSelect #: PS11750072
Manufacturer #: WPW10195623
This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack wil...
$49.67
In Stock
Dishwasher Drain Pump
PartSelect #: PS11753379
Manufacturer #: WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
$92.13
In Stock
Dishwasher Door Seal
PartSelect #: PS12348515
Manufacturer #: W11177741
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
$67.66
In Stock
Spinner Kit
PartSelect #: PS972316
Manufacturer #: 8193983
This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.
$29.58
In Stock
Dishwasher Upper Rack Roller
PartSelect #: PS11753471
Manufacturer #: WPW10350401
This assembly is the wheel and the mount for your upper dishrack. Sold individually. This is an authentic OEM part for use with Whirlpool, KitchenAid, Kenmore and Jenn-Air Dishwashers. The dishrack wh...
$42.48
In Stock
Rubber Washer
PartSelect #: PS11743934
Manufacturer #: WP717273
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
$7.77
In Stock
Tine Row
PartSelect #: PS10057161
Manufacturer #: W10728160
The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is...
$67.38
In Stock
Questions And Answers for KUDC10FXSS7
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Leslie Parks
March 14, 2020
Our 5 yr old KitchenAid dishwasher has just started to leak on the floor, during the main wash cycle.How can my husband fix it?
For model number KUDC10FXSS7
Hello Leslie, thank you for your question. We would suggest having a look at the door gasket to ensure it is free from food particles that may be causing gaps in the seal that the gasket creates. If there is a tear or rip in the gasket, you will need to replace this part. The door gasket is listed on our site as PartSelect number PS11731683. We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
May 2, 2024
Spinner on top of washer cannot be put back into place(does not snap in) the spinner looks ok. What is the part number for the spinner to be placed back.
For model number KUDC10FXSS7
Hello Michael, thank you for your inquiry. We would recommend carefully checking the upper wash arm spinner, part number PS972316, for damage. If the spinner is working fine, then we would recommend checking the water supply tube, part number PS11748132, to fix the issue. It is the part where the upper wash arm spinner attaches. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
WILLIAM
October 18, 2023
Where is the drain filter, and how is it removed?
For model number KUDC10FXSS7
Hello William, thank you for getting in touch. According to our research, the filter is located under the lower spray arm. We have attached the relevant video link, which will help you in removing the filter. Glad to be of help!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the KUDC10FXSS7
[Viewing 10 of 10]Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Parts Used:
-
Scott from Fort Lauderdale, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
624 of 664 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more
the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Read less
Parts Used:
-
Andrew from Alexandria, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
479 of 532 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull
... Read more
it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
Read less
Parts Used:
-
Steve from Inver Grove Heights, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
221 of 248 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!