Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Parts That Fix KitchenAid Microwave Oven Combo KEMC308KSS01 Will Not Start
Will Not Start is a commonly reported symptom for the KEMC308KSS01 KitchenAid Microwave Oven Combo, and we have put together a full guide on how to fix this.
This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your KEMC308KSS01 KitchenAid Microwave Oven Combo that will fix Will Not Start.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Ratings submitted by customers like you who bought this part.
An oven thermostat is a switch that opens and closes in response to the temperature it senses. It is typically found in the control panel, where a liquid-filled temperature-sensing bulb senses and maintains the internal oven temperature by cycling heat on and off. This safety thermostat trips when the controls are not working properly, or if the range gets too hot. If your oven will not start or is not heating properly, there could be an issue with the limit thermostat, and you should look to replace the part.
NOTE: Remember to disconnect the power from your range before you start this repair. This is an electrical appliance that can potentially hold a 220 volt charge.
$93.52
In Stock
PartSelect Number PS11747249
Manufacturer Part Number WP9759243
Replacing your Whirlpool Wall Oven Limit Thermostat
Customer Repair Stories
Oven wouldn't heat after cleaning cycle
Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.
Devin from Platte City, MO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
34 of 35 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat after cleaning oven
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your pow
... Read moreer cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.
Ratings submitted by customers like you who bought this part.
The temperature sensor measures the temperature inside the oven. If your oven is too hot, not heating evenly, is not heating enough when baking, or simply will not start, you could have a faulty temperature sensor. A faulty temperature sensor can be a fire risk. If your sensor is not working properly, you should look to replace it straight away. A failed oven sensor is most often responsible for F3 or F4 error messages on electronically-controlled ovens. Make sure you disconnect the power to your range before you start your repair.
$89.97
In Stock
PartSelect Number PS11748765
Manufacturer Part Number WPW10131825
Replacing your KitchenAid Wall Oven Temperature Sensor
Customer Repair Stories
Oven will not maintain set temp
Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem
Sam from TINLEY PARK, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bUILT IN OVEN NOT COMING UP TO TEMPERATURE
Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and conne
... Read morector back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install
Ratings submitted by customers like you who bought this part.
Sold individually.
$24.59
In Stock
PartSelect Number PS11745232
Manufacturer Part Number WP8203546
Replacing your Whirlpool Range Main Power Terminal Block
Customer Repair Stories
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Elizabeth from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Ratings submitted by customers like you who bought this part.
Also known as a meat probe.
$92.83
In Stock
PartSelect Number PS11747165
Manufacturer Part Number WP9755542
Replacing your KitchenAid Wall Oven Temperature Probe
Customer Repair Stories
Oven light bulb inop
Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts
... Read more for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.
Read less
Ed from Canyon Country, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
faulty meat probe
Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.
Kent from Seattle, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
38 of 65 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
