Parts That Fix KitchenAid Dishwasher KDTE104DSS0 Leaking
Leaking is a commonly reported symptom for the KDTE104DSS0 KitchenAid Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your KDTE104DSS0 KitchenAid Dishwasher that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
Replacing your KitchenAid Dishwasher Dishwasher Door Seal
Customer Repair Stories
leaking from door
-
charles from MAURICE, LA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
Leaking gasket
-
Larry from BENICIA, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The door seal is designed to seal the gap between the dishwasher tub and outer edge of the door. This helps to prevent leaks when your dishwasher is running. A leaking dishwasher is a good indication that the door seal is damaged. This seal is sold individually and is an OEM part sourced directly from the manufacturer.
Replacing your KitchenAid Dishwasher Seal
Customer Repair Stories
door leaks bottom right
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.
THANKS,
PETE GODSHALK
-
Peter from LEBANON, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
Door leaking from corner.
-
Don from GRAPEVINE, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
This is a seal, but you may also know it as a door gasket and it is for your dishwasher. The seal forms a watertight barrier between the door and the dishwasher tub, deterring water from escaping during a wash cycle. If your dishwasher is leaking you will need to replace the seal, as it is likely damaged. The first step should be to check the seal for buildup of food particles near the sides and the bottom of your appliance.
Replacing your KitchenAid Dishwasher Seal
Customer Repair Stories
Leak
2. Install new seal
-
Charles from WALLBACK, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
Leaking door seal
-
Charles from ELGIN, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Also know as a diverter valve. This diverter motor is for dishwashers. Diverter motor controls the flow of water to the spray arms. Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Replacing your Kenmore Dishwasher Motor
Customer Repair Stories
Leaking under the motor
-
John from PERRY, MO
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Diverter valve was leaking.
-
Dennis from PORTAGE, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
This drain hose is 6 and 1/2 feet.
Replacing your KitchenAid Dishwasher Drain Hose
Customer Repair Stories
Drain hose leaking
-
Robert from Beaufort, SC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Unwanted water.
-
David from PITTSBURGH, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Replacing your Whirlpool Dishwasher Dishwasher INLET VALVE
Customer Repair Stories
clean light blinked 4 times and repeated this over and over
-
Don from CLINTWOOD, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
Inlet valve wasn't working
-
Melissa from AIKEN, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.
Customer Repair Stories
Water leaking through the sump shaft seal
-
Jason from MOLINE, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Replacing your Kenmore Washer Hose Clamp
This pump inlet grommet is a genuine OEM replacement part that is compatible with various models of dishwashers. It is made of rubber and has a diameter of approximately 2.5 inches. The grommet is used to create a watertight seal in the area between the inlet hose and the circulation pump. This prevents the dishwasher from leaking, and it also helps to absorb minor shocks and vibrations that occur while the dishwasher is running. It is normal for the grommet to wear down over time or become damaged from exposure to water, heat, and chemicals.
Customer Repair Stories
I damaged the grommet when removing the recirc pump
-
john from SANFORD, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
WARNING!!! This is NOT the grommet that goes on the "pump stem" in the center
-
Monica from PITTSFORD, NY
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
This fill hose is a genuine OEM replacement part for your dishwasher. The hose is made of black plastic, and is accordion-style, for ease of movement within your dishwasher. To replace the fill hose, you will need a 1/4 inch nut driver, Channellock pliers, and a Phillips screwdriver. Replacing this part will require some disassembly, such as removing the water inlet valve from the fill hose, and the clamps which secure the hose in place. Reuse your existing clamps when securing your new fill hose in place.
Replacing your Whirlpool Dishwasher Inlet Fill Hose
Customer Repair Stories
The hose had a slit in it.
-
Larry from Sarasota, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Hole in filler hose
-
Gordon from Davidsonville, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
This part is used to drain water from your dishwasher.
Replacing your Whirlpool Dishwasher Drain Hose
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Replacing your Kenmore Washer Hose Clamp
Replacing your Whirlpool Dishwasher HOSE
Customer Repair Stories
hose had a hole and leaked
-
Christopher from Delaware City, DE
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
rat got under dishwasher and chewed water lines, grommet
also checked for rat entry points, plugged those and put down bait - bait wasn't being taken under dishwasher even tho rat reappeared so put a snap trap in back - no luck so far - teachable moment: might have been cheaper to just get another dishwasher as parts are expensive and its difficult to tell extent of damage - luckily i only needed 3 parts = $150
-
sharon from LAS VEGAS, NV
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
This is connected to the water valve, is located on the side of your tub and allows water to enter your dishwasher. ***Note: This part does not include the inlet gasket - must order separately.
This part is also known as a float switch. This float switch, when activated, stops the flow of water into the dishwasher.
Replacing your Whirlpool Dishwasher Overfill Control Switch
Customer Repair Stories
DISHWASHER WOULD NOT FILL WITH WATER
-
TRACEY ANN from BRICK, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
water fill overflows at times
-
Dennis from AUBURNDALE, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
Also known as a washer.
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Replacing your Whirlpool Dishwasher Dishwasher Drain Pump
Customer Repair Stories
Water not draining from the dishwasher
-
Frederick from BIG PRAIRIE, OH
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
dishwasher not draining after wash cycle
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
-
Andrew from Alexandria, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Used with the water inlet valve.
This is a flexible drain hose that is 12 feet long.
Replacing your Whirlpool Dishwasher Drain Hose
Customer Repair Stories
Installing a new dishwasher in a remodeled Kitchen
-
Maxie from Bridge City, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench set
Measures level of soil in the water.
Replacing your KitchenAid Dishwasher Turbidity Sensor
Customer Repair Stories
Failed diagonistics test for OWI sensor
-
Mark from Lancaster, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.
Replacing your KitchenAid Dishwasher Door Balance Link Kit
Customer Repair Stories
Door spring link broken
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i ... Read more nput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
5. Reverse (2 to 1) to reinstall the dishwasher.
-
Sean from Ramona, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Replaced Hinge Link
-
Scott from Fort Lauderdale, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Replacing your Whirlpool Dishwasher Diffuser
Shield
This is a door latch for various dishwashers. Door latches are designed to communicate with the control board of the dishwasher when the door is closed and latched shut. If your dishwasher is not latching shut properly, or if your dishwasher will not start when the door is shut, then this latch is likely broken or bad. To replace this door latch, you will need a screwdriver or drill, and a set of pliers. This latch is sold individually, and does not come with any securing screws or other parts.
Replacing your Whirlpool Dishwasher Door Latch - Black
Customer Repair Stories
Door latch wouldn't close
-
Colin from Goffstown, NH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Door would not latch shut
-
RONALD from PRESCOTT, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
Replacing your Whirlpool Dishwasher Lever
This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto the dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. The installation has been rated as "easy" by customers. Before beginning any repair, you should unplug the dishwasher and wear gloves to protect your hands. Check your model number and user manual to see if this part is right for you! Your dishwasher should have a left and right upper rack adjuster, and both are the same part. These parts are sold individually, so if you are looking to replace both, you will need to order two parts.
Customer Repair Stories
Original rack adjuster broken at retainer clip posts.
-
Richard from SIGNAL MTN, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
The original part broke down with use and needed to be replaced
-
Leon from FALLS CHURCH, VA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.
Replacing your KitchenAid Dishwasher Dishwasher Heating Element
Customer Repair Stories
Defective dishwasher heating element
-
Matthew from CHATHAM, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Wrench set
No heating for washing or drying
-
Dewey from UNIONTOWN, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
This filter works with the water pump in your dishwasher. It prevents debris from entering the pump and causing damage. As a result, the filter can occasionally become clogged or damaged, and will need to be replaced. A good indication of a damaged filter is if your dishwasher is not draining or cleaning the dishes properly. This filter has a gray plastic top and bottom that are approximately 5 inches in diameter. This is a genuine OEM part that comes directly from the manufacturer. To replace the filter, simply turn it counterclockwise to unlock, and then screw in the new filter
Replacing your Whirlpool Dishwasher Dishwasher Filter
Customer Repair Stories
Water filter needed replacing
-
Martha from SAN DIEGO, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
Dishwasher would not drain
-
Edward F from CINCINNATI, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
Replacing your Whirlpool Dishwasher MOTOR-PUMP
Customer Repair Stories
wash pump stopped working
-
christopher from MOSES LAKE, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
The plastic button covers the sharp ends of screws along the edge of the dishwasher tub. Sold individually.
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.
Replacing your KitchenAid Dishwasher Mounting Bracket
Customer Repair Stories
Broken Mounting bracket
-
Roy from HIGGINSVILLE, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Lost dishwasher brackets
-
Judith from Essex, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers