Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The utensil basket was old, bowed and the bottom was falling out.
I ordered a new replacement basket. The new one is a little different but it fits in the same place and takes up the same amount of room in the dishwasher. It looks very nice too.
The bottom of our dishwasher's old utinsel basket broke out
It was so easy to find the right part on the PartsSelect website. I just had to enter the manufacturer (Maytag) and model number and up popped skematics of all the parts available. I just clicked on the drawing of the basket and placed the order. It took less that 5 minutes. The part arrived 4 days later as promised. The repair took even less time than teh ordering. I simply took the old basket out and dropped in the new one.
I'm just happy to know there is a place that has such a user friendly website and stocks so many parts for older appliances. I had my house built in 1992 and several of the appliance are original. Fortunately I always keep the owners manuals for every piece of equipment so the model and serial numbers are readily available.
Most of the time was spent pulling out the dishwasher from under the counter, as a new tile floor had been installed after the DW was installed.
Great pictures of components on this website confirmed what part to order.
Shut off water feed to DW and disconnect power to DW.
Unplug wire connector to old valve (solenoid) and disconnect water inlet hose. Observe that valve is attached to sheet metal bracket.
Remove bracket, with valve attached. Don't remove valve from bracket. New valve comes with sheet metal bracket.
Remove female threaded adaptor (brass) from back of old valve and screw on to new valve using Teflon tape. That is the only piece you need to reuse.
Attached the new bracket (with valve attached) to DW. Attach water inlet hose. Attach plug to new valve.
Turn on water to DW. Check for leaks. Retighten hose connection if required. Run dishwasher. Keep lower panel off for a couple of days to be certain no leaks develop.
Ordered replacement basket online at much better price than available localy. When I recieved it discovered that it did not include the handle, but was suprised to see it labeled as "Genuine Maytag Parts" ( I realy expected a knock-off replacement part for the price difference). I was able to remove tha handle from the old basket and install it on the new one. Job done. No problem
5 of the 8 wheels on the lower dishwasher rack had broken off
I simply snapped the new wheel assemblies back on. The main thing I want to say is that I have never owned a dishwasher that required replacing wheels and I believe there is a design flaw in the wheel that they break so easily. If you look at the way they are mounted on the rack, eventually the weight of dishes on the rack will wear them out and break them. It cost me nearly $50 to replace them all. I bought extras because I know more will break in the future.
Dishwasher would fill properly but when wash cycle would start you could not hear any water spraying.
First I removed the lower spray arm by removing the middle retainer nut. Next remove the 3 screws holding the outer shroud in place. Next remove 6 screws holding the water pump top housing in place. Under this housing you will find the impeller which is retained by a screw. Check the impeller closely for cracks especially near the center hex portion of the impeller. Replace if you have any doubt of it's integrity. Next remove the lower pump housing that has the screen material in the center. What I found was the nylon part that attaches to the shaft of the motor was stripped so the impeller would spin in it's normal direction ( counterclockwise) but under the load of water it would not. So I ordered a new impeller and seal kit with a metal sleeve and chooper blade. Follow the instructions provided in the new kit a reassemble accordingly.
I had to remove the 4 screws holding the toe panel. Then I had to take out the one screw holding the floater switch housing in place. It snapped open to release the floater and that just lifted out. I put the new float in and snapped the new housing on. I put the screw back in to hold the housing in place attached the two wires to the switch and put the toe panel back on. It was all very easy to do and my first home repair went very well. thank you.
Wash motor not pumping and making a grinding sound
I went to PartSelect and found the parts pictorial. A replacement motor was listed for 3 series of the dishwasher. The series can be identified by the first 2 digits of the dishwasher serial number. Mine was 22 so I needed parts for the series 20 dishwasher.
According to the pictorial it looked like the motor seals were included with the replacement motor. When the motor arrived, I found the seals were not included. I called PartSelect and they shipped the seals to me with free overnight delivery.
I had no trouble disassembling the wash manifold and spray parts using the instructions provided with the replacement motor and the instructions from the Maytag repair manual that I found online. The motor is removed from the inside of the tub.... very nice. You don't need to remove the dishwasher from under the counter in order to get at the motor.
I made a mental note of the orientation of the faulty motor before I removed it. I installed the replacement motor with the same orientation along with the wash parts. The dishwasher worked successfully.
After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.
Our dishwasher would run for 1 min, stop then run for 1 min then stop completely.
We ordered a Control Panel first (not sure what part we really needed to fix the problem). After installation and the Control Panel didn't solve the problem, we knew we needed the Circuit Board. We then ordered the Circuit Board and upon receipt itstalled it. The Circuit Board was simple to install and BINGO! It worked perfectly. Thank you for have the parts we needed.
Dishwasher wouldn't stay on without pushing on door due to faulty switch.
Removed plastic lining from dishwasher door with torx screwdriver, then removed screw holding door latch assembly in place. Removed existing switch from door latch assembly and replaced.
This switch was not the correct one initially as it was a normally closed switch, whereas the existing switch was a normally open. Was able to pry open the switch and switch the contacts to normally open so it worked out in the end. Would recommend purchasing the complete latch assembly w/ switches if you aren't comfortable taking the switch apart.
Pulled the dishwasher out. Determined that it was leaking from the air/water inlet. Ordered the seal and replaced the seal by turning the inside cover counter clockwise while holding the outer water inlet. Replaced seal and installed water hose. Put dishwasher back inside cabinet and leveled. If you don't try to fix it yourself, It could cost more then what it is worth.