Make sure you haven't got the discount earlier.
Parts That Fix General Electric Washer GCWP1800D1WW Will not agitate
Will not agitate is a commonly reported symptom for the GCWP1800D1WW General Electric Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GCWP1800D1WW General Electric Washer that will fix Will not agitate. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This is a dual-action agitator for a washer. It is an OEM replacement part that is sourced from the manufacturer. The agitator tosses your clothes to clean them efficiently. This plastic dual-action agitator is white in color. It is approximately 18 inches tall with a base diameter of about 12 1/4 inches. No tools are required for this repair. Your agitator has eight tabs that fasten on the drive block of your washer, which is driven by the transmission. This part does not include the agitator coupling kit, which is frequently purchased at the same time as the agitator.
Replacing your General Electric Washer Dual Action Agitator
Customer Repair Stories
Two paddles on the agitator broke off.
-
Karen from Hamilton, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Blades broken off agitator
-
Michael from Itasca, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Bolt not included. This part connects the transmission drive shaft to the agitator base.
Replacing your General Electric Washer Agitator Coupling
Customer Repair Stories
No Agitation Spins OK
-
Raymond from TRAVELERS RST, SC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
not agatating
-
pilar from covert, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
Replacing your General Electric Washer 6-Rib Drive Belt
Customer Repair Stories
Broken belt.
-
Mike from Meridian, ID
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
broken drive belt
-
jon from barry, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
This lid switch with wire harnesses is used in washing machines. The pin on the lid switch pushes onto the lever of the switch to communicate to the machine that the washer lid is closed. If your washing machine is not running when the lid is closed, not spinning, draining, or agitating, replacing the lid switch could solve the problem. The tools needed for this repair are: putty knife, 1/4 inch nut driver, wire strippers and crimpers. Refer to the manual for further installation instructions. Remember to unplug your washer from the power source as a safety precaution.
Replacing your General Electric Washer Lid Switch with Wire Harness
Customer Repair Stories
Washer didn't wash/spin
-
Eva from NAPLES, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
washing machine would not go through all cycles or agitate
-
Brian from Millerplace, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
Replacing your General Electric Washer Tub Dampening Strap
Customer Repair Stories
Noticed 3 straps were broken when we replaced the hose
-
Christine from Tempe, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
loud noise upon aggitation
-
Robert from Covington, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
This part is a replacement fabric softener dispenser for your washer. If your washer will not dispense fabric softener or detergent, or will not agitate, you may need to replace the dispenser. When it is working, the dispenser releases fabric softener during the wash cycle. You can find the dispenser screwed in to the top of the agitator. To replace the dispenser simply unscrew it, and replace it with a new one. This is an OEM part, and is sold individually.
Replacing your General Electric Washer Fabric Softener Dispenser
Customer Repair Stories
There was no fabric softener dispenser
-
Norma from Holiday, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
There was no fabric softener dispenser
-
Gigi from Monroeville, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Replacing your General Electric Washer MAGNET Assembly
Customer Repair Stories
water, spin cycle not functioning
-
Helmut J from New Berlin, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This split ring is supplied by the original equipment manufacturer, and it is designed to secure the tub bearing in washing machines. It is a circular metal ring, with an outer diameter of 2 inches. The ring has a split or gap, which allows it to expand and contract for easy installation and removal. It is typically located on the inner side of the washing machine outer tub, where it provides stability and prevents the washer from excessively shaking during use. It is normal for the split ring to become worn, corroded, or damaged due to age, exposure to moisture, and excessive stress. A faulty split ring will lead to a noisy, unstable washer and eventually cause the tub assembly to fall out of alignment. Remove the washer panels to access the outer tub and split ring. Carefully detach the damaged split ring from the tub and position the new split ring in its place. Ensure that it is properly aligned and securely fastened before reattaching the panels.