Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.75
In Stock
Order within the next 4 hrs and your part ships today!
The shelf retainer bar end cap is used to keep the retainer bar in place, and can be used on either the right or left hand side of the bar. This white, OEM end cap is approximately 2 inches long, and ...
$10.71
In Stock
Order within the next 4 hrs and your part ships today!
This refrigerator door shelf trim is approximately 28 inches long. It is all white in color, and it is made entirely of metal. NOTE: The image may not be of the exact product but will function properly.
$54.87
In Stock
Order within the next 4 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.83
In Stock
Order within the next 4 hrs and your part ships today!
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If you are noticing temperature issues with your refrigerator or freezer,...
$66.85
In Stock
Order within the next 4 hrs and your part ships today!
This defrost timer will cycle for twenty-one minutes after every ten hours of run time.
The defrost timer acts like a clock. It continually advances and alternates between activating the cooling cy...
$123.03
In Stock
Order within the next 4 hrs and your part ships today!
This hinge can be used for washers and refrigerators. The hinge is used to easily open and close your appliance door. If you put too much pressure or weight on the door, it can break the hinge or the ...
$14.56
In Stock
Order within the next 4 hrs and your part ships today!
Questions And Answers for CTN1511GEW
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the Hex head small screw at the middle back of the Back wall of the fridge above the top shelf. Removed the 2 small Hex Head screws that go into the of the Plastic cover upwards into the top roof of the fridge. I ended up with an extra screw so I dont know what I did... The hard part is pushing up on the two tabs, one on
... Read more each side in the extreme back on the bottom of that white plastic cover. You have to pull the coverwhile releasing the tab (locks) by pushing UP. The Right side was easier, I got that side to release and drop down. But the left side took some pressure on the tab with a fat screwdriver. Then you have to kinda of Bend the cover to get it to slide out...
Then take out the 2 phillips screws above the light bulbs. the left side one is tricky, need long skinny driver.
Drop assembly down and on the back right is the ADP board. Mine was a bare board but the replacements are enclosed in white plastic that fit in place just fine.
Pry connector off of the board carefully and drop new plastic circuit board case in and replace.
Put a thermometer in a glass of water. unplug fridge for 10 minutes and then plug it in. Give it a few hours.. Everything seems fine. A steady 39 degrees with the Fridge control at a few ticks right of middle. I have no idea what it was before my troubles... But 36 - 41 seems to be what you need.
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
remove back lower panel using nutdriver. Locate and remove Relay and Overload parts from side of Compressor which were located inside a small white box shaped cover unti held on by a spring clip. Attach new Relay and overload to 3 pin terminals on side of compressor. Attach 1 white & 1 orange/white wire to relay terminals. Attach supplied
... Read more white jumper wire to Overload and other end to Blue wire. Instal new cover supplied with kit replacing old box type cover.