Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Top four burners on oven would not light without using match
Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. There are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off. Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
My wife wanted different color stove top grate & burner caps.
Called GE for part number crossover from gray to black and asked for an email quote. Called Parts Select for pricing, which was alot lower! Shipping took five days and less then $8.00 buck....now mama's happy!!!! Thanks for great frendly service from Mike in California.
Simiple repair. Determined drip pan size (sm, med., lg.) removed 2 screws holding drip pan, placed gasket around new drip pan and installed. Repaired took less than 5 minutes.
Removed the two screws holding the porcelain burner bowl. Disconected the electric igniter by removing the "w" clip on the underside of the bowl. Then disconnected the igniter from the electric supply cord. Reverse these directions using the new urner bowl. Really easy.
electronic ignitors would not stop firing even when burner was off
first I removed all the srews from the burners that hold the glass cooktop. I then disconected the two wires from the damaged gas valves and replaced them all four with the new ones. After that I put it all togehter and work just fine and celebrated with a good cold beer.
Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.
Replacement cook-top, had natural gas orifices, needed propane
Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.
stove top burner ignition spark progressively got weaker and then stopped on all but one burner.
I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!
Pulled off burner grates, burner, unscrewed burner bowl, removed clip from igniter and wire, then put it all back together. Was very easy, and the stove looks like new again.
PartSelect is very good with amazing shipment times. The kjpart arrived much sooner than expected.
The most difficult part of the repair was getting the front panel off. I needed to remove the top of the stove, which was easy but awkward - remove the two screws from each of the four burner bowls. Lift the bowls one by one, disconnect the wire and slide off the small clip under each igniter. Move the bowls and igniters out of the way. You will find a piece of sealant underneath the stove top covering the length of the front panel. You need to gently pry it off by lifting the stove top just enough to break the seal. Once the top is separated just gently move it to the back of the stove. You can now remove the 3 large screws underneath the front panel. There are also 2 screws under the plastic anchors that hold the front panel in place. Be careful, there are hidden screws in the back of each anchor, so don't break them. You just need to loosen them just enough to wiggle the front panel out. With the panel moved, the igniter switches are mounted over each knob. There is a spring washer clip holding them down. Gently pry off the clip of the damaged switch and disconnect the two wires. Make sure you put the wires back in the same order.
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.
No way to adjust mixer tube assembly so the mounting holes will line up with the holes in the burner bowl. Mounting holes in bowl should be slotted to prevent future problems. Had to finally bend the mixer tube mounting bracket enough to get one bowl on. It also made the procelin break on that bowl because the screw put to much pressure on the side of the hole.
Igighter mounting hole out of position just enough to prevent the burner head from sliding over it and sitting on the mixer tube correctly.
I solved this problem by fileing the opening slot for the igniter. Even with the igniters being just a little out of alignment from the original position they still light well.
I did not get new gaskets for the burner bowl but would reccommend that you get them.
Replaced igniter pins but no joy, needed igniter module
Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.