Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The interior light in your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, or stays on when the door is closed...
$31.60
In Stock
Order within the next 10 hrs and your part ships today!
This water tube, or plastic tube, is used in refrigerators and freezers. The tube ensures water is directed to parts of the refrigerator that need it, such as the water dispenser and ice maker. If you...
$16.95
In Stock
Order within the next 10 hrs and your part ships today!
This OEM filter measures 2.5 inches deep, 12.5 inches high, 5 inches wide and roughly 1.5 lbs. It is recommended to replace this filter every six months or 300 gallons, whichever comes first. If you n...
$86.79
In Stock
Order within the next 10 hrs and your part ships today!
The door stop, or door stopper, is used in refrigerators. This door stop helps keep the door in position and in balance. This part is attached to the bottom of the door and it keeps it from opening an...
$13.59
In Stock
Order within the next 10 hrs and your part ships today!
This part is sold individually. This part is white plastic on the outside and metal on the interior, with a hole in the middle. The roller assembly is found in your refrigerator. You will find this pa...
$29.64
In Stock
Order within the next 10 hrs and your part ships today!
This lamp cover is also commonly referred to as a light lens. This is a genuine replacement part. It is used in a refrigerator to cover the light bulb. It is made of clear plastic. It measures 14 inch...
The purpose of the door latch cam is to keep the door latched when you shut it. If your door is not staying shut, you may need to replace the door latch cam. This part is made of white plastic and is ...
The wire harness is NOT available separately. Refrigerator ice maker kit AEQ36756901 is an original equipment manufacturer (OEM) part that fits some refrigerators in these series: Kenmore 795; Kenmore...
$305.52
In Stock
Order within the next 10 hrs and your part ships today!
Questions And Answers for 77564
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have cont
... Read moreinuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.
Ordered a new tank assembly, but the new part also leaked because it had a hole in it. Ordered another that worked fine. Used a flat head screwdriver to remove the clips covering the screw holes to the tank assembly cover, then a phillips to remove the cover screws and the screws retaining the tank. Did not use the tubing that came wit
... Read moreh the new tank (removed it by taking out the neck clip then simultaneously pushing back on the neck piece while pulling out the hose). Used this same procedure to remove the old tank at both positions. Installed the new tank, replaced the clips, pressurized/tested the system and put the cover back on. Overall less than a 5 minute job...except for the extra week waiting for a good part.