Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Easily pulled old gasket from channel. Soaked new gasket in warm water. Cleaned debris from channel with wire brush and CLR. Starting at top-middle, gently pressed new gasket in place. Used a gentle push-pull technique on the corners. Used fingers to smooth gasket all around. Closed door and kept latched for 2 hours. Ran dishwaher to check for leaks.
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.
After unscrewing the dishwasher, I pulled out the washer, I saw that the springs were attached just by strings that were broken... I just used the strings from an old lanyard, retied everything, and did not need the springs! works well!
First, I replaced the bottom door seal. You will need magnetic nut drivers because of the location of the 3/16 screws that hold the seal in place. you also need a 1/4 in nut driver to remove plastic cover that covers up the 5 3/16 screws. Last you need a small star driver to remove the door screws. Note 4 of the door screws, the 4 on top of the door are much longer than the side screws. With all this said, this seal was not my problem. I then replaced the large black rubber seal around the tub. Be sure if you do this you fold the seal in half and start in the middle of the top of the opening so you have the exact amount of seal left over on both sides. Also when you remove the old seal, clean the area it was removed from with a damp cloth. Turns out, That was not my problem either. So now I will move to the next step to see where the water is coming from but maybe this information will help someone with a simple door leak.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Inoperative door latch replaced by a redesigned latch
1. Disconnect power at the breaker, 2. remove two wood screws fastening the dishwasher to the cabinet and slide the unit out approximately 2 inches. 3. Remove old latch strike and replace with redesigned strike. 4. Slide unit in and reattached to cabinet. 5. Remove 11 screws holding inner panel of door assembly and one screw holding user interface unit to door. 6. Disconnect snap cable to latch assembly and replace the latch unit. 7. Reassemble.
Unplug the dishwasher,take the screws out of the coutertop,then slide dishwasher out turn it on its side. Then take a torx screwdriver and remove 2 mounting screws. Unplug the wires going into the motor and replace the motor with the new one. But you need to replace the grommet the motor shaft slides up into or it will still leak.
All of the wheels had broken off and the bottom rack was hard to move.
It was very easy to pry off the old wheel assemblies with a screwdriver and pop the new ones in place. Although the part is called "wheel" it is actually the plastic piece containing two wheels. I thought it was a little confusing to just call it "wheel" as each piece has two wheels. It was an easy repair.