Lawn Tractor Accessories Parts

Your Price

$4.99

PartSelect Number PS16477373

Manufacturer Part Number 997027001

This OEM blade adapter is made of high-quality metal and is compatible with various models of lawnmowers and lawn tractors. It connects the lawnmower blade to the crankshaft, allowing the blade to rotate freely and cut grass effectively. This adapter has one keyway/tab, a full-circle, and half-circle, on each side of it to lock the blade to the crankshaft. Failing to replace this adapter could result in poor cutting performance, and increased wear on other components like the crankshaft, and could pose a serious safety threat. To replace this adapter, you will need to prop/wedge your lawnmower up on some wood to access the cutting deck. You will also need a wrench to loosen and remove the bolt securing the blade and adapter to the crankshaft. Replacing this adapter is as simple as tapping it lightly with a hammer to jostle and carefully remove it, and then install the new one.

Line Cut-Off Blade – Part Number: 638016003

Your Price

$3.99

Lawn Tractor Accessories Line Cut-Off Blade

★★★★★

3 Reviews

PartSelect Number PS16389742

Manufacturer Part Number 638016003

This OEM line cut-off blade trims any excess or protruding string from your trimmer during operation so that it stays at an optimal length within the guard. It is in the guard assembly at the bottom of the trimmer head near the rotating spool where the trimmer line is fed. Over time, it can become dull or worn out. Look for signs of damage such as deformation, bending, or nicks. If not replaced, the trimmer may produce uneven or messy trims and put additional stress on the spool or motor, leading to premature wear or damage. To replace the blade, locate it on the grass deflector assembly and remove its mounting screws. Please note that this blade is sold individually without hardware.

Installation Instructions

William from SPANISH FORT, AL

Noise and wobbles during spin cycle.

Ordered the hub repair kit. I had much difficulty removing the agitator. It was stuck. Running the strap under it and tapping on the agitator assembly should've caused it to pop up but didn't. I had to ultimately strike it hard with a metal hammer. That released it but caused a hole in the agitator. The center metal gear on the agitator was very worn and rusty. I decided to also replace the agitator. I saved about $300 on the repair. Read more...

Your Price

$4.99

Lawn Tractor Accessories Pin, Shear, 1-3/4

PartSelect Number PS9999468

Manufacturer Part Number 703063

Shear Pins are designed to break off in order to prevent further damage to your machine. Because they are designed to break, we recommend having a few spares on hand. This part is made of metal, is silver, is not part of a kit or assembly, and is sold individually. A Shear Pin will break when you hit a large chunk or ice or other debris. Once it is broken, it will need to be replaced. You will need pliers to complete this repair. Customers rate this repair as Easy.

Your Price

$3.99

Lawn Tractor Accessories Nut-Lock, Ni

PartSelect Number PS8953555

Manufacturer Part Number 3296-42

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

Your Price

$6.21

Lawn Tractor Accessories Bearing

★★★★★

3 Reviews

PartSelect Number PS9006914

Manufacturer Part Number 532009040

The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in question, or you notice the wheel is sloppy on the shaft. You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.

Installation Instructions

robert from EUREKA, CA

transaxle rotated forward on 2015 Husqvarna YT42DXLS

2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair.

HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.

HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.

HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.

HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.

HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.

HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...

Cap Axle Black 1 50 x 1 00 – Part Number: 532104757

Your Price

$3.99

Lawn Tractor Accessories Cap Axle Black 1 50 x 1 00

★★★★★

1 Review

PartSelect Number PS9007667

Manufacturer Part Number 532104757

This genuine black cap axle, also sometimes known as the dust cap, is around 2 inches in diamater and sold individually. Comprised of plastic, it is designed to keep debris out of the hub and axle of your lawn mower or garden tractor. Over time, your dust cap may become damaged or lost due to wear and tear. If this happens, dirt and debris can freely enter the axle and hub, causing damage. This is an easy repair to make and does not require any tools. Just look for the cap axle on the rim of the wheel to make your repair.

Installation Instructions

Anthony from OLIVEHILL, TN

Wheel bushings were bad

Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side. Read more...

Your Price

$4.99

Lawn Tractor Accessories Shear Bolt

PartSelect Number PS9002923

Manufacturer Part Number 51001500

This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, inspect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

Installation Instructions

Dennis from WESTFIELD, MA

Switch return spring broken

Removed panel, unsrew switch assy. Remove electric connector s, reverse process to reinstall Read more...

Ring Klip Number T5304-75 – Part Number: 812000029

Your Price

$3.99

Lawn Tractor Accessories Ring Klip Number T5304-75

★★★★★

1 Review

PartSelect Number PS9143890

Manufacturer Part Number 812000029

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

Installation Instructions

Anthony from OLIVEHILL, TN

Wheel bushings were bad

Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side. Read more...

Shear Pin, .25 – Part Number: 738-04124A

Your Price

$3.99

Lawn Tractor Accessories Shear Pin, .25

PartSelect Number PS9110822

Manufacturer Part Number 738-04124A

This individually sold shear pin is an OEM replacement that is most typically used in snowblowers but can also be used within snowblower attachments for lawn tractors. Its main uses are connecting the auger and auger shaft, which are the rotating blades, and to protect more valuable components such as the transmission.If the snow is causing excessive force or there is a jam within the auger and connected housing,it will cause the shear pin to snap, effectively stopping the rotation of the auger, while the auger shaft and gears will continue turning. If the shear pin snaps, snow will simply build up on the outside of the auger housing, since the auger will no longer spin. This shear pin has a .25-inch diameter, and 1.5-inch length and is sold individually. Most augers have a pin on each side, so you may need to purchase more than one, and it is also recommended that you carry spare pins in case of a future breakage.