KitchenAid Cooktop Igniters

Your Price

$41.57

KitchenAid Cooktop Burner Electrode

★★★★★

12 Reviews

PartSelect Number PS11744318

Manufacturer Part Number WP74009336

This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replacement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Dennis from Iredell, TX

Simple to change, but you do need a torx bit screwdriver.

Remove screws holding burner down, invert and remove screw in igniter. Reverse to reinstall. Read more...

Your Price

$43.26

KitchenAid Cooktop Surface Ignitor

★★★★★

1 Review

PartSelect Number PS11747432

Manufacturer Part Number WP9782116

Also known as Spark Electrode. This part helps your burner ignite and produce flame.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Roland from Houston, TX

Igniter problem on one gas burner

I had to remove the two separate components of the gas burner unit, each had two screws. I lifted then tilted the lower portion of the burner unit to allow access to the underside of the igniter. I removed the wire and then with an offset screwdriver I removed the single screw that held the igniter in place. I reversed the steps to install the replacement, very quick fix.

I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping. Read more...

Your Price

$49.02

KitchenAid Cooktop Spark Electrode

★★★★★

3 Reviews

PartSelect Number PS11740866

Manufacturer Part Number WP3185804

This part helps your burner ignite and produce flame.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Billy from Martinsville, IN

There was a crack in the porcelain not letting it spark

I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner. Read more...

Your Price

$24.42

KitchenAid Cooktop Surface Igniter

PartSelect Number PS11727815

Manufacturer Part Number W10833887

Installation Instructions

Ronald from ROSEVILLE, CA

Surface ignitor not working on one burner

Disconnect power and turn off gas. Remove all grills, knobs and burners. Under the burners are 2 Phillips head screws. Remove all 10 screws. Remove surface plate. Remove the one igniter with problem. There is a small metal clip holding it in place. Remove the wire. Install new ignitor and reverse all steps above. Read more...

Your Price

$25.73

KitchenAid Cooktop Igniter-SURF

★★★★★

1 Review

PartSelect Number PS11731309

Manufacturer Part Number W10854967

Your Price

$60.40

KitchenAid Cooktop Surface Ignitor

PartSelect Number PS11754239

Manufacturer Part Number WPW10398577

Installation Instructions

Elbert from SAN TAN VLY, AZ

Would not spark

Pull top off and replace the wire Read more...

Your Price

$51.00

KitchenAid Cooktop Igniter-SURF

★★★★★

1 Review

PartSelect Number PS2325067

Manufacturer Part Number 8286723

Installation Instructions

FRANCIS X from LAKE ELSINORE, CA

center igniter needed replacement

Turn off gas and unplug cooktop. Lift off the 3 grills. Lift off the cast iron and aluminum burner parts. Lift off the five control knobs, noting that the middle knob has a thicker stem.Find star bit that fits the machine screws around each burner. Start removing with the bit in a nut driver. If you have to use a 1/4 inch socket for some, try not to break or strip the screws or the bit. Apply heat with a propane torch if stuck hard. After that, lift stainless tray off. Lift out foil pad. Mine was the center burner igniter. Using two wrenches each side, disconnect gas lines from each side. Phillips head to disconnect plate from burner. The igniter is held in place with spring and clip. Unplug igniter wire from electronic box. I used a hemostat so as not to lose the spring clip .Spring can be removed at the plug end of the wire. A big allen key fits the one inch wide middle burner part - remove it. Now pull the old igniter out through the top of the burner. Use a small round file to make the igniter hole smoother and maybe slightly larger. Thread new igniter through hole, plug end first. Spring and clip on bottom are hard to get. Try not to lose the clip- It can spring off into space.Plug igniter wire into electronic box. I used an anti-seize compound on all threaded parts. Go carefully in reverse order . Plug in cooktop and turn on gas. test new igniter. Good luck Read more...

Your Price

$253.21

KitchenAid Cooktop Surface Burner Igniter Electrode with Wire

PartSelect Number PS356929

Manufacturer Part Number 4175453

Sold Individually.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

David from Bishop, CA

Porcelain sleeve broke

Due to the age of the appliance, the screws were almost fused to the burner. I used a spray lubricant and broke the screws free with an impact screw driver. It was pretty easy with this type of driver. This avoided stripping the screws which would have occurred with a regular screw driver. The installation was easy and it all works like a charm! Read more...