Jenn-Air Range Igniters
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Jenn-Air Range Igniters
Your Price
$57.79
In Stock
Jenn-Air Range Flat Style Oven Igniter Kit
PartSelect Number PS1573892
Manufacturer Part Number 12400035
The flat style oven igniter kit is used in gas ovens and ranges. It is what provides the heat needed to open the gas valve, and it ignites fuel for the burner assembly. This part can be used for both bake and broil elements, and it can replace both short and long igniters. However, it cannot replace round style oven igniters. If your igniter glows for 90 seconds or more without igniting the burner, this means it is too weak to open the valve. The element in your igniter may have shorted it and it might not glow at all, or it might only glow orange or red. It needs to glow white hot; if it cannot get hot enough the gas will not be released from the safety valve and it will be impossible to light the burner in your oven. This kit includes the igniter, ceramic wire nuts, an insulation pad, a metal bracket, a variety of plug ends, and an instruction sheet. The body length is 3 3/4 inches, and the element inside is approximately 1 1/2 inches. This replacement part has an amperage range of 3.3 to 3.6. The element inside this igniter is extremely fragile, do not touch it. Before you start repairing your oven or range, make sure you have unplugged it and shut off the gas supply.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Gas smell
- See more...
Installation Instructions
James from Ferndale, MI
Oven would not work but the Broiler did
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside.
Read more...
Your Price
$93.48
In Stock
Jenn-Air Range Oven Igniter - Vertical Mount Bake and Broil
Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.
Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.
I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.
Keep track of your screws and put it back together the way you found it except for the igniter that is.
Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.
Good luck. Read more...
PartSelect Number PS2085070
Manufacturer Part Number 74007498
This broil igniter assembly comes with its own metallic mounting bracket and a 7-inch-long dual wire lead with a plastic plug. This part will need to be repaired if your oven element is giving off no heat or very little, or is not heating evenly. You may also notice a smell of gas. The ignitor may still be glowing, but could still have gone bad. You will need a 1/4-inch nut-driver and a 5/16 nut-driver. Open the oven door and pull the door off the hinges to completely remove. Pull out the racks. Using your 1/4-inch nut driver, take out the screws at the bottom rear end of the oven, which will allow you to completely remove the bottom. Unscrew the nuts holding the igniter in place. Remove the igniter with the 5/16 nut driver. You should now have access to remove the old igniter.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Gas smell
- See more...
Installation Instructions
James from Berwick, ME
Oven wouldn’t heat up properly
My oven has two igniters so I needed to determine which one was the problem. Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.
Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.
I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.
Keep track of your screws and put it back together the way you found it except for the igniter that is.
Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.
Good luck. Read more...
Your Price
$41.20
In Stock
Jenn-Air Range Top Burner Igniter
PartSelect Number PS2082000
Manufacturer Part Number 74004053
This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
roy from East Providence, RI
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read more...
Your Price
$41.57
In Stock
Jenn-Air Range Burner Electrode
PartSelect Number PS11744318
Manufacturer Part Number WP74009336
This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replacement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Dennis from Iredell, TX
Simple to change, but you do need a torx bit screwdriver.
Remove screws holding burner down, invert and remove screw in igniter. Reverse to reinstall.
Read more...
Your Price
$25.35
In Stock
Jenn-Air Range Surface Burner Spark Igniter
PartSelect Number PS11746068
Manufacturer Part Number WP8523793
This part helps your burner ignite and produce flame.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Daniel from Needham, MA
spark igniter was weak and not lighting the flame.
Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together.
Read more...
Your Price
$87.08
In Stock
Jenn-Air Range Oven Bake Igniter
PartSelect Number PS11752876
Manufacturer Part Number WPW10324262
Fixes these symptoms
- Gas igniter glows, but will not light
- Little to no heat when baking
- Will Not Start
- See more...
Installation Instructions
Mark from HOLLAND, MI
Faulty ignitor
Remove bottom plate take screws and hex head nuts remove wire unscrew ingnitor reverse process with new ignitor very easy
Read more...
Your Price
$47.20
In Stock
Jenn-Air Range Spark Ignition Electrode
PartSelect Number PS11757464
Manufacturer Part Number WPY0316773
This spark ignition electrode lights the gas that starts the burner on your range or cooktop. This electrode is part of the burner assembly, sits next to the burner head, and is just over an inch in length. It pulls current from the ignition circuit; the more current it pulls, the warmer it gets. When the spark ignition electrode reaches a certain temperature, it creates a spark. This electrode comes with the mounting bracket you will need to successfully install the part. Before installing your new part, shut off the gas supply and unplug your appliance. This part cannot be repaired. If it is damaged or faulty, it must be replaced.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
HUY from ALISO VIEJO, CA
Broken Electrode, no spark
Remove 2 screws holding the top burner. Remove 1 screw holding the electrode. Remove electrode from wiring using plier. Install new electrode and top burner
Read more...
Your Price
$86.55
In Stock
Jenn-Air Range Spark Igniter Set
PartSelect Number PS11744110
Manufacturer Part Number WP74005890
This part provides the spark to the burners.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Patricia from Overland park, KS
Spark igniter out
The primary spark igniters failed. Take the (small) screws out of the sides and bottom of the pan. The front of the pan must be removed from the bottom, because the front burner igniter wire is too short to allow reassembly once attached. Only other is the screws for the attachment bracket are larger than the holes. Suggest routing them out slightly to get them to grip the screws. Otherwise it is quite simple. Pull the connections with a needlenose and press the new wire connection back on firmly. Screw the screws back in the pan.
Read more...
Your Price
$61.76
In Stock
Jenn-Air Range Spark Module - Surface Burners
PartSelect Number PS2003170
Manufacturer Part Number 12001596
This part may differ in appearance, but functions same as original part. : This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
jonathan from Bryson City, NC
No spark at top burners, first one then eventually all 4.
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, located inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks!
Read more...
Your Price
$24.42
In Stock
Jenn-Air Range Surface Igniter
PartSelect Number PS11727815
Manufacturer Part Number W10833887
Installation Instructions
Ronald from ROSEVILLE, CA
Surface ignitor not working on one burner
Disconnect power and turn off gas. Remove all grills, knobs and burners. Under the burners are 2 Phillips head screws. Remove all 10 screws. Remove surface plate. Remove the one igniter with problem. There is a small metal clip holding it in place. Remove the wire. Install new ignitor and reverse all steps above.
Read more...
Related Jenn-Air Range Parts
- All Jenn-Air Range parts
- Jenn-Air Range Brackets and Flanges
- Jenn-Air Range Circuit Boards and Touch Pads
- Jenn-Air Range Cooktops
- Jenn-Air Range Doors
- Jenn-Air Range Drip Bowls
- Jenn-Air Range Elements and Burners
- Jenn-Air Range Grates
- Jenn-Air Range Hardware
- Jenn-Air Range Hinges
- Jenn-Air Range Insulations
- Jenn-Air Range Knobs
- Jenn-Air Range Legs and Feet
- Jenn-Air Range Lights and Bulbs
- Jenn-Air Range Panels
- Jenn-Air Range Racks
- Jenn-Air Range Seals and Gaskets
- Jenn-Air Range Switches
- Jenn-Air Range Valves
- Jenn-Air Range Wire Plugs and Connectors
