Generator Seals and Gaskets
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Generator Seals and Gaskets
Your Price
$5.83
On Order
Your Price
$5.19
In Stock
Generator Air Cleaner Gasket
PartSelect Number PS9138757
Manufacturer Part Number 795629
The Air Cleaner Gasket is used to provide a seal between the air cleaner base, and carburetor. It's a gray, composite material part, which is rated as "Easy" to install and will require a screw driver, pliers, socket set, and nut driver. It attaches between the base of the air cleaner assembly and carburetor. If broken, damaged or worn down it will allow dirt to enter the carburetor, causing performance issues. If this happens, replace it. Refer to your make, model and diagrams to check if this is the right part.
Your Price
$5.71
In Stock
Generator Gasket--Exhaust
PartSelect Number PS9294808
Manufacturer Part Number 692236
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice the presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.
Installation Instructions
FRANK from EASTANOLLEE, GA
Screw can out of the carburator throttle baffel and stuck in the exhaust valve
No compression. Removed the cylinder head. freed the screw, checked the valve to see if it still sealed. Turned the head over with the valves in it, install a spark plug, fill the head dome with gas and see if any leeks out over a 2 hr period. If not you are good to go. Reinstalled every thing with new gaskets and a new carburetor screw. Set the valves to spec. Complete the rebuild and there you have it. Rebuild the carburetor while you have it apart. This motor runs great !!!
Read more...
Your Price
$6.59
In Stock
Generator Seal,Oil
PartSelect Number PS9277860
Manufacturer Part Number 391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. Refer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.
Your Price
$8.09
On Order
Your Price
$4.99
In Stock
Generator Gasket-Intake
PartSelect Number PS8941014
Manufacturer Part Number 27355S
Installation Instructions
Gerald from MAULDIN, SC
Replace fuel diaphragm, fuel pickup tube and air cleaner
This 5hp B&G was manufactured in 1985! Had been garage kept and always dependable. After 10 years of non use the carb wasn't getting gas. Removed air cleaner box, muffler and crankcase breather to easily remove carb, replace parts and reassemble.
Read more...
Your Price
$5.34
In Stock
Generator Gasket-Exhaust
PartSelect Number PS9063564
Manufacturer Part Number 690970
Installation Instructions
george from HALLWOOD, VA
valve problem causing pushrod damage
pinged valve guide reinstalled head with new gasket inserted rods adjusted valve 15 min. later mowing lawn first time doin such repair note used magnet to pull old rod inside engine to drain left in rotated engine maling sure no parts broken started up and away i went c how long it lasts mower had over6500 hrs.. on it
Read more...
Your Price
$4.99
In Stock
Your Price
$5.99
In Stock
Generator Seal-Oil
PartSelect Number PS8948679
Manufacturer Part Number 299819S
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to your make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.
Your Price
$6.91
On Order
Generator Gasket-Cylinder Head
PartSelect Number PS8941204
Manufacturer Part Number 272157S
The cylinder head gasket, also known just as the head gasket, is an OEM part sold individually. Grey in color, the head gasket provides a seal between the cylinder head and the engine block in your engine. Over time, it can become damaged due to wear. You may also need to replace this part any time you have had to remove the cylinder head for any other reason, as the gasket is a one time use.
If you suspect your head gasket is damaged, perform a compression test. In doing so, you may hear air escaping from the head gasket area, and you will know this part is responsible. Symptoms that can be exhibited if this part needs replacing include an engine lacking power. Most of our customers thought this was a medium-difficulty repair.
The repair requires a wrench or sockets and a torque wrench. When re-installing your head gasket, torque in an alternating patter to the manufacturer specifications for a proper seal.
