Frigidaire Dryer Elements and Burners
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Frigidaire Dryer Elements and Burners
Your Price
$170.04
In Stock
Frigidaire Dryer Heating Element Assembly
1) Remove the two screws from the rear / upper panel (below the control panel).
2) Snap the front side using a flat head screw driver.
3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.
4) Remove the rear motor access panel (two screws) and appying tension to the spring remove the belt.
5) Pull the drum upwards (verticaly) unnapping it from the rear wall and remove it horizontally through the front panel.
6) Disconect the four leads to the heating element and remove the four screws from the rear of the dryer and replace the heating element.
Follow the same steps backwards to put the dryer together again. Read more...
PartSelect Number PS418120
Manufacturer Part Number 131553900
This dryer heating element produces heat to dry clothes and is located in the rear of a dryer. If the heater element is burned, the dryer does not heat or over heats, or clothes are taking too long to dry, replacing this part could solve your problem. The tools needed for this repair project are a Phillips screwdriver, putty knife, and needle nose pliers. To repair, first remove the main top of the dryer and ground strap at the rear. Disconnect the two wire harnesses and remove the screws that hold the front panel to the cabinet, in order to pull out the front panel. Now that you have access to the inside of the dryer, refer to the manual for further installation instructions and detailed guidance. Remember to unplug your appliance from the power source before beginning this repair project.
Fixes these symptoms
- Noisy
- Not Heating
- Too hot
- See more...
Installation Instructions
Juan Carlos from Weston, FL
short circuit with a brasier metal support
Disconect the dryer from the main power source.1) Remove the two screws from the rear / upper panel (below the control panel).
2) Snap the front side using a flat head screw driver.
3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.
4) Remove the rear motor access panel (two screws) and appying tension to the spring remove the belt.
5) Pull the drum upwards (verticaly) unnapping it from the rear wall and remove it horizontally through the front panel.
6) Disconect the four leads to the heating element and remove the four screws from the rear of the dryer and replace the heating element.
Follow the same steps backwards to put the dryer together again. Read more...
Your Price
$204.50
In Stock
Frigidaire Dryer Heater Element
PartSelect Number PS2349309
Manufacturer Part Number 134792700
This part is a heater, but may also be known as a heating element, and it is meant for your dryer. This is where the heat is generated during your machine cycle in order to properly dry your clothing. This model is a 5500 watt, and has three coils. If your heater is broken, that usually means there is a break in the coil element.If you are having trouble drying your clothes, you may want to check for a thermal cut out or a blown thermal fuse. For this repair you will need a number two square bit, a Phillips screwdriver, and a flat-head screwdriver.
Fixes these symptoms
- Not Heating
- Too hot
- See more...
Installation Instructions
Steven from MARIETTA, GA
Dryer wasn't heating properly, drying took too long.
Removed back of dryer with electric nut driver. Lots of screws. Removed old heating element to better access wires and thermostats. Removed baffle at end and transferred to new heater element. Transferred thermostats to new element, reconnected wiring in correct order. Installed new heater element in correct position using tab to locate. Replaced back of dryer. Reconnected dryer vent. Toughest part was squeezing out of space after reconnecting dryer vent. Unfortunately, too short for my weight.
Read more...
Your Price
$80.45
In Stock
Frigidaire Dryer Heater Coil with 5/16 Inch Terminals
While greasing the bearing in the back of the drum, I found my heating coil was broken. Steps to replace:
1) Unplug the unit
2) Remove the top panel. Note, do not remove the center front screw that does not go into the door.
3) Remove front outer panel
4) Remove interior front panel
5) Remove front control panel 6 screws, pushing downward the panel and disconnecting connection to door.
6) Remove door by removing the screws on the top and pull door straight off. (I left the air duct attached to the door)
7) Remove the back access panel to the motor
8) Release the belt from the idler pulley and remove the belt.
9) I removed the three screws in the center of the drum as I found it difficult to remove the drum from the bearing. Remove the drum.
10) disconnect the coil terminals by first bending the tabs outward to allow you to be able to pull them off the block
11) remove the old coil
12) carefully stretch the new coil so that it measures 48 inches (no more)
13) Plug new coil into terminals and bend tabs to lock in place.
14) Divide heater coil in half and install coil onto center support on the opposite side from where it connects to the block/back wall of dryer
15) Install remaining coils onto supports.
16) reinstall all parts in reverse order. Read more...
PartSelect Number PS451032
Manufacturer Part Number 5300622034
Coil only.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Mark from Normalville, PA
Dryer would not heat
First..kudos to PartSelect for their fantastic support! Great work folks.While greasing the bearing in the back of the drum, I found my heating coil was broken. Steps to replace:
1) Unplug the unit
2) Remove the top panel. Note, do not remove the center front screw that does not go into the door.
3) Remove front outer panel
4) Remove interior front panel
5) Remove front control panel 6 screws, pushing downward the panel and disconnecting connection to door.
6) Remove door by removing the screws on the top and pull door straight off. (I left the air duct attached to the door)
7) Remove the back access panel to the motor
8) Release the belt from the idler pulley and remove the belt.
9) I removed the three screws in the center of the drum as I found it difficult to remove the drum from the bearing. Remove the drum.
10) disconnect the coil terminals by first bending the tabs outward to allow you to be able to pull them off the block
11) remove the old coil
12) carefully stretch the new coil so that it measures 48 inches (no more)
13) Plug new coil into terminals and bend tabs to lock in place.
14) Divide heater coil in half and install coil onto center support on the opposite side from where it connects to the block/back wall of dryer
15) Install remaining coils onto supports.
16) reinstall all parts in reverse order. Read more...
Your Price
$175.15
In Stock
Frigidaire Dryer Heater Assembly
PartSelect Number PS2378363
Manufacturer Part Number 131475320
This dryer heating assembly has 5/16" terminal on the housing.
Installation Instructions
CAROLE from MONTICELLO, AR
Dryer still turned, but would not heat
Had to remove tub to get to rear wall to make the repair and then put it back together in reverse order.
Read more...
Your Price
$210.30
Special Order
Frigidaire Dryer Heating Element Assembly
PartSelect Number PS2367792
Manufacturer Part Number 137114000
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.
Your Price
$30.93
In Stock
Frigidaire Dryer Heating Element Restring Coil with 1/4" Terminals
PartSelect Number PS451031
Manufacturer Part Number 5300622032
This part is located behind your dryers drum.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Kevin A Frech from Sidney, IA
bearing and heating element broke
Had to first remove the top of the dryer this was done by removing the clamps on the back. Next I removed the front of the dryer by removing the two nuts the frong in the inside, these are somewhat hard to reach. Next the drum was removed. then the heating element shield. Replaced, the heating element then secured it into place. replaced the drum bearing assembly, and put back together.
Read more...
Your Price
$154.41
In Stock
Frigidaire Dryer Heating Element Coil Kit
PartSelect Number PS449327
Manufacturer Part Number 3937010
This kit includes the heating element restring coil, 2 insulators and a terminal block.
Your Price
$133.14
Special Order
Your Price
$37.30
Special Order
Your Price
$23.01
Special Order
Related Frigidaire Dryer Parts
- All Frigidaire Dryer parts
- Frigidaire Dryer Brackets and Flanges
- Frigidaire Dryer Circuit Boards and Touch Pads
- Frigidaire Dryer Doors
- Frigidaire Dryer Hardware
- Frigidaire Dryer Hoses and Tubes
- Frigidaire Dryer Knobs
- Frigidaire Dryer Panels
- Frigidaire Dryer Seals and Gaskets
- Frigidaire Dryer Switches
- Frigidaire Dryer Thermostats
- Frigidaire Dryer Timers
