Dishwasher Valves
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dishwasher Valves
Your Price
$57.03
In Stock
Dishwasher Water Inlet Valve - 120V 60Hz
PartSelect Number PS1990907
Manufacturer Part Number 154637401
This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. The water inlet valve on your dishwasher supplies water to the dishwasher. If your dishwasher is leaking because it has overflowed, the water inlet valve may be the cause. If your dishwasher continues to fill above the heating element, try opening the door latch to see if it stops filling. If it continues to fill, you have a defective inlet valve that will need to be replaced.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
CHRIS from ROANOKE, VA
Water leaking from Inlet Valve
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first place and messed up my subfloor and laminate flooring.
Read more...
Your Price
$64.02
In Stock
Dishwasher INLET VALVE
PartSelect Number PS12578165
Manufacturer Part Number W11175771
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Will not fill with water
- See more...
Installation Instructions
Melissa from AIKEN, SC
Inlet valve wasn't working
Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done
Read more...
Your Price
$48.27
In Stock
Dishwasher Water Inlet Valve
Turned off the breaker for the dishwasher. Turned off the water supply valve. Unscrewed the screws in the panel that hides the parts under the dishwasher. Unscrewed the screws anchoring the dishwasher to the counter. Slid the dishwasher out about a foot. Inlet valve was located on the front left side of the dishwasher. Unclipped the wire harness. Placed a cookie sheet under the water line. Unscrewed the water line from the inlet valve. Unscrewed the two Phillips head screws holding the valve to the dishwasher frame. Got the new part. Put the screws back into the frame. Reconnected the water line and wire harness. Slid the washer back into place. Turned on the water valve. Watched for leaks. Turned the breaker back on and started the cycle. Watched for leaks. Once I saw there weren’t any replaced the screws anchoring it to the counter and replaced the cover on the bottom. That was it! Took me longer to type out the steps than it did to actually do the repair. Read more...
PartSelect Number PS9865067
Manufacturer Part Number 807047901
This water inlet valve is for dishwashers.
Water inlet valve supplies water to the dishwasher.
Unplug the dishwasher and shut off the water supply before installing this part
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Will not fill with water
- See more...
Installation Instructions
CHERI from CREEKSIDE, PA
Dishwasher was not filling up at the start of the cycle.
This was really easy. Have done it before on other older dishwashers in the past. Turned off the breaker for the dishwasher. Turned off the water supply valve. Unscrewed the screws in the panel that hides the parts under the dishwasher. Unscrewed the screws anchoring the dishwasher to the counter. Slid the dishwasher out about a foot. Inlet valve was located on the front left side of the dishwasher. Unclipped the wire harness. Placed a cookie sheet under the water line. Unscrewed the water line from the inlet valve. Unscrewed the two Phillips head screws holding the valve to the dishwasher frame. Got the new part. Put the screws back into the frame. Reconnected the water line and wire harness. Slid the washer back into place. Turned on the water valve. Watched for leaks. Turned the breaker back on and started the cycle. Watched for leaks. Once I saw there weren’t any replaced the screws anchoring it to the counter and replaced the cover on the bottom. That was it! Took me longer to type out the steps than it did to actually do the repair. Read more...
Your Price
$43.82
In Stock
Dishwasher Water Inlet Valve
You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.
You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.
Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.
Reverse the order and reconnect everything and you should be good to go!
Double-check for any leaks prior to pushing everything back in :) Read more...
PartSelect Number PS3654179
Manufacturer Part Number WD15X10014
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Greg from Burlington, VT
Water leak, small puddle to front left of dishwasher
You'll need to remove the front toe kick and (if installed, the GE Profile baffling for additional silencing action). You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.
You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.
Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.
Reverse the order and reconnect everything and you should be good to go!
Double-check for any leaks prior to pushing everything back in :) Read more...
Your Price
$59.50
In Stock
Dishwasher Water Inlet Valve
PartSelect Number PS11749213
Manufacturer Part Number WPW10158389
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
MICHELLE from EDEN VALLEY, MN
water leaking out of bottom of machine
removes the 1 screw that held the old one in and removed the water lines the supply line with a adjustable wrench and the internal line had a hose clamp on it then i just went in reverse...
Read more...
Your Price
$62.85
In Stock
Dishwasher VALVE
PartSelect Number PS3496157
Manufacturer Part Number 5304482406
Fixes these symptoms
- Leaking
- Will not fill with water
- See more...
Installation Instructions
Paul from Belmont, CA
Water leaking out onto floor when not in use!
Remove front Fascia on floor, use AC sniffer find hot wires into unit. Flip circuit breaker at panel. Verify no AC, shut water valve off on Dishwasher supply. Disconnect two valve wires to solenoid. Use wrench set to find proper size and use to remove supply line. Unscrew two Phillips sheet metal screws that hold valve support bracket and remove bracket with it now being held in by water inlet valve hose to interior wall of Dishwasher. Use Tin Snips to cut off metal band securing hose to old water inlet valve. Place new valve onto inlet hose, secure with new hose clamp (you must supply) tighten hex nut on clamp till water tight. Fasten wires onto the solenoid and mount assembly support bracket to dishwasher. Now connect water supply line after wrapping threads with pipe dope tape fasten and secure nut with adjustable wrench till water tight open supply valve and look for leaks with a flash light. If no leaks, reset breaker and test run and drain. No leaks replace fascia and have a Beer great Job saved $850 min. on a new dishwasher!
Read more...
Your Price
$61.52
In Stock
Dishwasher Water Inlet Valve
PartSelect Number PS8760080
Manufacturer Part Number W10648041
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Will not fill with water
- See more...
Installation Instructions
Bruce from GRANDVIEW, MO
Your Price
$24.34
In Stock
Dishwasher Piston and Nut Assembly
PartSelect Number PS260690
Manufacturer Part Number WD24X10018
This is used for the check valve.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Dan from Minnetonka, MN
Dishwasher wouldn't fully drain
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem.
Read more...
Your Price
$36.05
In Stock
Dishwasher Drain Valve Shaft Seal
PartSelect Number PS263930
Manufacturer Part Number WD8X181
The drain valve shaft seal is a part for your dishwasher drain pump valve. This seal creates a watertight closure around the flapper valve shaft. This part can be accessed through the access panel at the front for a built-in. For a portable dishwasher, consider disconnecting and unplugging the taps and lay on a blanket to access the bottom of the machine. This will need to be replaced if you notice leaking coming from the pump. This part measures approximately 3/8 inches in diameter and is black in color. This is a genuine OEM part that comes right from the manufacturer.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Joseph from Livermore, CA
Water leak from gate (diverter) valve shaft
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect.
Read more...
Your Price
$55.46
In Stock
Dishwasher Water Inlet Valve
Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers. Read more...
PartSelect Number PS11730996
Manufacturer Part Number W10844024
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. NOTE: As per the manufacture this part has been updated from the original part. It may be a different color, and you may need to order an elbow (# W10685193) for the new designed valve to work.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
David from Lexington, NC
Inlet valve was leaking from crack in brass fitting
Removed the lower panels from beneath the dishwasher door. 4 screws. Turned off the water.Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers. Read more...
