Dishwasher Sensors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dishwasher Sensors
Your Price
$33.73
In Stock
Dishwasher Turbidity Sensor
PartSelect Number PS11757214
Manufacturer Part Number WPW10705575
Measures level of soil in the water.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Mark from Lancaster, NY
Failed diagonistics test for OWI sensor
Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.
Read more...
Your Price
$33.19
In Stock
Dishwasher SENSOR
PartSelect Number PS8727335
Manufacturer Part Number 00611312
Fixes these symptoms
- Door latch failure
- Door won’t close
- Will Not Start
- See more...
Your Price
$63.62
In Stock
Dishwasher SENSOR
PartSelect Number PS12070543
Manufacturer Part Number W11084121
Fixes these symptoms
- Not cleaning dishes properly
- See more...
Installation Instructions
Melvin from SACRAMENTO, KY
would not shut off.
easy the sensor was on the right side, and easy to get to, I turn off the power, turned off the water, and pulled it out, the first thing I saw was the yellow wires and plug. took about 5 minutes, to replace it.
Read more...
Your Price
$46.44
In Stock
Dishwasher SENSOR
PartSelect Number PS8727345
Manufacturer Part Number 00611323
Fixes these symptoms
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Daniel from AUBURN, IN
dishwasher not draining, dishes dirty
replacing the sensor was simple, just unplug and turn it out, but didn't solve the problem, it's a float sensor that doesn't show up on the tech sheet in the dishwasher or anywhere in troubleshooting on the internet I could find.
Read more...
Your Price
$61.75
In Stock
Dishwasher Turbidity Sensor
PartSelect Number PS2363559
Manufacturer Part Number 154762601
Fixes these symptoms
- Leaking
- See more...
Your Price
$117.49
In Stock
Dishwasher Thermistor
Removed access plate
Disconnectd water and drain
Removed anchor screws
Pulled unit out and disconnedted from Electric
Flipped on it's back
Ohmed out all heat related items and found discrepency with Thermisitor resistance
Ordered and received Part
Changed out Thermisitor
Checked wiring to Heater and replaced connections
Hooked electric up
Ran Diognostics per Maintenance flyer and cleared fault
Hooked back up and ran like a champ
The reason it took so long is because I put the old thermisitor back in and tryed to run the diognostics just to make sure that was the problem Read more...
PartSelect Number PS11745500
Manufacturer Part Number WP8269208
This part is used to regulate water temperature when certain cycles or options are selected. The thermistor is part of the sensor mounted in the tub.
Fixes these symptoms
- Not cleaning dishes properly
- Will Not Start
- See more...
Installation Instructions
Deb from LaPorte, IN
Stopped Running,Will Not Start, and Clean LED Blinks 7 times then repeats
Got Maintenance Flyer out an read about problemRemoved access plate
Disconnectd water and drain
Removed anchor screws
Pulled unit out and disconnedted from Electric
Flipped on it's back
Ohmed out all heat related items and found discrepency with Thermisitor resistance
Ordered and received Part
Changed out Thermisitor
Checked wiring to Heater and replaced connections
Hooked electric up
Ran Diognostics per Maintenance flyer and cleared fault
Hooked back up and ran like a champ
The reason it took so long is because I put the old thermisitor back in and tryed to run the diognostics just to make sure that was the problem Read more...
Your Price
$161.99
In Stock
Dishwasher Turbidity Sensor
PartSelect Number PS816014
Manufacturer Part Number 154473901
The sensor measures level of soil in the water and the thermistor is used to regulate water temperature when certain cycles or options are selected.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$29.74
In Stock
Your Price
$25.59
In Stock
Dishwasher SENSOR TURBIDITY Assembly
The first thing i checked was the drain filter which was clogged. I took shop vac and sucked all the excess water out and removed the flood switch. seemed ok but you can't tell if its ok, so just replace it. I then removed the door from the unit. I needed to replace the dispenser. After the door was off I tilted the machine forward, to check the heater. I pulled the quick connects off and checked the resistance across the heater, should be 16 ohms mine was 16.3 so heater not bad. looking at the bottom of the machine, follow the left hand wire and it will attach to a thermal overload. (a small round disc which is not listed in the parts manuals ), I checked for continuity across the switch it was open.
On this model GE the switch is resettable, a small reset button in the middle of the overload. I reset it and continuity was restored. only three things might cause this to kick. one the flood switch, the vent fan or the turbidity sensor. I replaced all three and the machine is working great.
If you have replaced your heater and still doesn't heat, try resetting that switch. and give GE a big thank you for not telling any one about the switch.
A big thank you to PartSelect for having all the correct replacement parts. Read more...
PartSelect Number PS7783361
Manufacturer Part Number WD21X10494
Installation Instructions
Gary D. from ALBUQUERQUE, NM
The GE Cafe series Dishwasher not drying dishes.
I pulled the dish washer out and, make sure you turn off the power, disconnect the water and drain line. un screw the mounting screws. The first thing i checked was the drain filter which was clogged. I took shop vac and sucked all the excess water out and removed the flood switch. seemed ok but you can't tell if its ok, so just replace it. I then removed the door from the unit. I needed to replace the dispenser. After the door was off I tilted the machine forward, to check the heater. I pulled the quick connects off and checked the resistance across the heater, should be 16 ohms mine was 16.3 so heater not bad. looking at the bottom of the machine, follow the left hand wire and it will attach to a thermal overload. (a small round disc which is not listed in the parts manuals ), I checked for continuity across the switch it was open.
On this model GE the switch is resettable, a small reset button in the middle of the overload. I reset it and continuity was restored. only three things might cause this to kick. one the flood switch, the vent fan or the turbidity sensor. I replaced all three and the machine is working great.
If you have replaced your heater and still doesn't heat, try resetting that switch. and give GE a big thank you for not telling any one about the switch.
A big thank you to PartSelect for having all the correct replacement parts. Read more...
Your Price
$49.32
Special Order
