Air Conditioner Hoses and Tubes

Videos!

Your Price

$54.46

Air Conditioner Faucet Adapter

★★★★★

22 Reviews

PartSelect Number PS11751238

Manufacturer Part Number WPW10254672

The faucet adapter for your portable dishwasher or washing machine attaches to the faucet and allows you to connect the machine to the tap. Before you install the faucet adapter on your taps, be sure that it fits the coupler on your dishwasher or washer. As per the factory, this is used for faucets with inside or outside threads. For female connection (outside) just remove the washers. This adapter is approximately 1 inch in length, and slightly less than one inch in diameter. This adapter comes with two different thicknesses of rubber washer. You will not need to use both so be sure to determine which thickness works best for your tap before installing it.

Fixes these symptoms

Leaking
Will not fill with water
See more...

Installation Instructions

Stephen from Enfield, CT

faucet attachment would not sit correctly in hose connector to portable dishwasher. Received machine second hand. Could not find a replacement faucet adapter. So ordered new one and hose plus connector.

Turned machine on side. Removed two casters with Wonder Tool prybar. Then used it to remove plastic push screws holding cardboard bottom cover. Unscrewed water hose. Used screwdriver to remove clamp on drain hose. Stood machine upright, opened door. Unscrewed two screwsfrom tabs into woodblock top. Slid top forward and removed it. Cut plastic hose retainer. Removed hose assembly. Installed new hose by reversing steps. Used a new wire strap to hold hoses in place on top corner of machine. Read more...

Your Price

$47.29

Air Conditioner Faucet Adapter Coupling

★★★★★

4 Reviews

PartSelect Number PS7321390

Manufacturer Part Number 5304490369

A faucet adapter coupling allows the user to connect their dishwasher to their kitchen faucet, and this coupling acts as a bridge between the faucet and intake hose for its various compatible dishwashers. This coupling features a plastic end with a mainly metal construction and a threaded section near that plastic end to screw into the faucet, whereas the other end connects to an intake hose that feeds into the dishwasher. This faucet adapter coupling is sold as an individual OEM part without any other hoses or connectors but does come with smaller components inside, such as O-rings and a spout adapter. If you notice water leaking from the connector area of this adapter on your dishwasher, it is likely that the adapter has some form of O-ring deterioration, thread wear, or mineral buildup and needs to be replaced. To replace this adapter, make sure your dishwasher and sink are off, and then simply thread this adapter onto the end of your faucet and connect the non-threaded end into the hose.

Installation Instructions

Liza from Hazel Park, MI

Purchased used appliance that needed parts

I purchased a wonderful portable dishwasher at a garage sale for $20. The woman had just redecorated her kitchen and was selling the relatively new portable model. All it needed was a new caster and a faucet adapter. After ordering the parts, they arrived in a couple days, and after less than 5 minutes of installing them I had a "new" dishwasher that works like a champ! Thanks for making this so easy! Read more...

Your Price

$15.89

Air Conditioner Hose Clamp Kit

★★★★★

2 Reviews

PartSelect Number PS270806

Manufacturer Part Number WH1X2036

This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in diameter while the larger one is 2 inches in diameter. The hose clamps secure the end of the water hose in place to prevent the hose from leaking. If you notice leaking from the hose of your appliance, you may need to replace this kit. Protect your hands with work gloves during this repair to avoid injury.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Richard from Garden City, NY

washer had heavy wet clothes left after spin cycle

The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump. Read more...