Crosley Dryer Drums and Tubs

Videos!

Your Price

$14.73

Crosley Dryer Front Glide Kit

★★★★★

38 Reviews

PartSelect Number PS1804752

Manufacturer Part Number 306508

The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. While you have the front bulkhead removed for this repair, you may want to inspect the felt that lines it. If the felt is damaged, it is recommended that you replace it at the same time. You will need a rivet tool for this installation, as well as a stubby Phillips screwdriver, a 5/16 nut driver, and a drill with a 1/8-inch bit.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

John from Charlottesville, VA

Belt broke on old machine.

1. Removed front of machine (2 screws at the bottom).
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.

I also cleaned the lint from the cabinet and from the vent hose.

In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.

I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...

Videos!

Your Price

$28.08

Crosley Dryer Drum Glide - White

★★★★★

15 Reviews

PartSelect Number PS5574052

Manufacturer Part Number 137513300

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each drum glide is approximately 33 inches in length. If the following symptoms occur, consider replacing the drum guide as a solution: dryer is noisy, will not tumble, or leaves marks on clothes. Remember to unplug the power source to the dryer before installing this part. Refer to the diagram provided by the manufacturer for further instructions and guidance.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Sergio from Cromwell, CT

Clothes were getting caught in gap, leaving burn mark.

Took the face off, and replaced the worn down drum glide and felt. Works just fine now. Read more...

Videos!

Your Price

$14.20

Crosley Dryer Drum Glide

★★★★★

10 Reviews

PartSelect Number PS11741931

Manufacturer Part Number WP37001298

If your dryer is noisy, will not tumble, or is leaving marks on your clothes, you may need to replace the drum glide. The drum glide is installed on the front bulkhead either at the top or the bottom, regardless of the brand of dryer. To gain access to the drum glide, you will have to open the cabinet on the dryer. This drum glide is sold individually but it is important to note that they should be replaced in pairs. Before beginning this repair, it is important to disconnect the dryer from the power source. The tools required for this repair are a putty knife and a 5/16 nut driver.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

David from Underwood, IA

Loud banging sound. Worn out roller.

Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all. Read more...

Videos!

Your Price

$58.83

Crosley Dryer Two-Piece Split Ring Bearing

★★★★★

10 Reviews

PartSelect Number PS334199

Manufacturer Part Number 279441

This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during operation, or if there are marks left on your clothes after a cycle, you may need to replace the bearing ring kit. The kit comes with 2 bearings, one for the top and one for the bottom of the dryer drum. Remove the front panel of your dryer to access the dryer drum for this repair. At this point you can use a pair of needle nose pliers to release the old bearing rings from the drum. Snap the new bearing rings on, and reassemble the dryer to complete your repair.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Edward from Andover, NJ

Dryer was sqeaking loudly when running

I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan Read more...

Videos!

Your Price

$41.70

Crosley Dryer Tall Baffle

★★★★★

14 Reviews

PartSelect Number PS11741085

Manufacturer Part Number WP33002032

This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle. NOTE: Screws are NOT included.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Teresa from Pace, FL

dried too many shoes and broke the baffles

removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there. Read more...

Videos!

Your Price

$46.09

Crosley Dryer Short Baffle

★★★★★

20 Reviews

PartSelect Number PS11741064

Manufacturer Part Number WP33001755

This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Teresa from Pace, FL

dried too many shoes and broke the baffles

removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there. Read more...

Videos!

Your Price

$60.85

Crosley Dryer Cylinder Glide Bracket

★★★★★

2 Reviews

PartSelect Number PS11741912

Manufacturer Part Number WP37001036

These brackets support each side of the tub. Order quantity needed.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Jeffrey from Medina, OH

Noisy - Clothes getting stuck between drum and bulkhead

1) Removed lower panel
2) Removed door
3) Removed Front Panel - removed connectors from switch and marked connections
4) Removed Front Bulkhead
5) Glides and Felt pads were missing, and brackets were nearly worn through
6) Removed and Replaced old brackets
7) Attached self-adhesive felt pads
8) Attached Drum Glides
9) Removed old felt seal
10) Glued new felt seal in place with 5-min epoxy
11) Allowed Epoxy to set and stop stinking
12) Re-attached front bulkhead
13) Re-attached remaining parts

Dryer works great, is quiet again, and no longer eats clothes!!!!!! Read more...

Your Price

$59.43

Crosley Dryer Drum Front Bearing Ring

★★★★★

2 Reviews

PartSelect Number PS11741470

Manufacturer Part Number WP3394509

This part mounts to the front of the drum.

Fixes these symptoms

Noisy
See more...

Your Price

$30.13

Crosley Dryer Drying Rack - Dimples 9.5" apart

★★★★★

2 Reviews

PartSelect Number PS346509

Manufacturer Part Number 3404351

This Whirlpool/Kenmore made dryer drying rack is great for drying shoes and other items that cannot tumble dry. This dryer rack fits whirlpool made dryers that are 29 inches wide, have the letter "E" following the numbers in the model number, and whose dimples are nine and a half inches apart in the back of the dryer drum.

Installation Instructions

Robert from BLOOMINGTON, IL

I was sent a drying rack for my electric dryer

The drying rack sent matched the dimples,9.5 inches apart, but it was an inch and a half too long. The rack sent was 21 inches, I need a rack that is 19.5 inches long. So I returned it. At TWICE the cost of the rack itself. Still in search of a rack that will fit my dryer Read more...