Whirlpool Dryer Brackets and Flanges

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Whirlpool Appliance Parts
Shop By Part Type

Popular Whirlpool Dryer Brackets and Flanges

Your Price
$43.43
  In Stock
Whirlpool Dryer Bearing Retainer
PartSelect Number PS266696
Manufacturer Part Number WE1M300
There is a slot in it for a ground strap.
Fixes these symptoms
Installation Instructions
Kerry from New Martinsville, WV
Noisy like a chain rattling inside
Disconnect Power from the Dryer
Remove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unhooked the belt from the tensioner and motor pulley.
Pulled the drum out. Removed the belt.
Removed the three screws that held the bearing assembly
on the back of the drum.
Removed the keeper o-ring slide the bad bearing off of shaft. Slide the new bearing on the shaft put the new o-ring on the shaft. Reassembled the bearing on back of the drum. Put belt back around the drum and put drum back in place. Put The belt around the motor pulley and tensioner
(this is probably the hardest part).
Put the front and top back together.
Turned the power back on. Job done Read more...
Your Price
$62.53
  In Stock
Whirlpool Dryer STACK KIT FOR LONG VENT DRYER
★★★★★
★★★★★
1 Review
PartSelect Number PS12069913
Manufacturer Part Number W10869845
Installation Instructions
Nelson from Middletown, NY
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board. Read more...
Your Price
$11.36
  Special Order
Whirlpool Dryer Bracket
PartSelect Number PS11756997
Manufacturer Part Number WPW10656504
Your Price
$51.84
  In Stock
Whirlpool Dryer Stacking Kit
★★★★★
★★★★★
6 Reviews
PartSelect Number PS888067
Manufacturer Part Number 8541503
This kit comes with 2 adhesive pads, 2 brackets and 4 screws. This is for stacking the appliances vertically - dryer over washer.
Installation Instructions
Randy from Brentwood, CA
Placing Dryer on Top of Washing Machine with Stack Kit
I purchased a stack kit from "Part select.com". The item was just what I needed to do the job. The delivery of the part was made the next morning. WOW! Excellent service! The process was completed in less than 24 hours, start to finish. Very impressed! Read more...
Your Price
$48.18
  In Stock
Whirlpool Dryer Stacking Kit
★★★★★
★★★★★
2 Reviews
PartSelect Number PS990537
Manufacturer Part Number 8572546
This kit allows you to stack your washer and dryer to maximize your laundry space.
Your Price
$60.37
  In Stock
Whirlpool Dryer Plate
PartSelect Number PS11750411
Manufacturer Part Number WPW10208419
Your Price
$54.58
  Special Order
Whirlpool Dryer BRACKET
PartSelect Number PS352092
Manufacturer Part Number 3979115
Your Price
$14.53
  In Stock
Whirlpool Dryer Bracket, Ignitor
PartSelect Number PS11743787
Manufacturer Part Number WP694298
Your Price
$74.64
  In Stock
Whirlpool Dryer Glide Bracket Kit
PartSelect Number PS2003560
Manufacturer Part Number 12002090
This kit contains two glide brackets and four screws.
Fixes these symptoms
Installation Instructions
David from Underwood, IA
Loud banging sound. Worn out roller.
Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all. Read more...
Your Price
$34.90
  On Order
Whirlpool Dryer BRACKET
PartSelect Number PS351723
Manufacturer Part Number 3976435
Installation Instructions
randy from simi valley, CA
bad drum rooller bearing
took the top, sides and back removed the drum and replaced the roller roller shaft and drive belt and the belt tensioner Read more...

Related Whirlpool Dryer Parts

Back to Top