This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found...
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place o...
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble,...
This v-shaped spin belt helps transfer power from the motor to the transmission to help pump the water in and out of the washer. It also helps runs the spin cycle in the washer.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs ...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal...
$8.02
In Stock
Questions And Answers for SWT520WA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
This was the second time for the repair. The original bearing lasted 5 years then became noisy. Replaced it, and the unit worked great 5 more years and the noise came back. So I knew exactly what needed fixing what to order, parts wise. This is not a project for the faint of heart, you will completely disassemble your washer to change
... Read more out the main bearing. Roughly here are the steps: 1, pull out the agitator with a good firm jerk up. 2, remove the rubber plug in the center of the drive hub, 3 remove the bolt you have just exposed. 4, pry up on the hub, use a puller if you have to to remove it. 5, pry off the cone shaped rubber seal and remove the large main nut from the drive shaft. 6, remove the 4 bolts holding tub, 7 remove the front panel and unscrew the front of the top panel, tip the top up. 8, lift out the tub, 9, remove the 6 large springs holdig the inner assembly to the base, 10, disconnect the water to tank hose and the fill level hose, 11, disconnect the motor cable at the motor, 12, free up the drain hose and pull it, 13, have a helper lift the inner assembly out and move it to a work area, 14, unbolt the drum from the base, motor, and counter weight 15, pry the drive hub off the transmission shaft, 16, remove the rubber seal from the drum, 17 flip the drum and remove the 3 bolts holding the bearing in place. Reverse to put it back. These steps are from memory so they may not be exact. The exploded views on PartsSelect.com web help, as to the instructions that come with the parts.
FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two screws, one on the left side, and one on the right, remove these screws, and pull slightly down on panel to remove. Behind this panel find two s
... Read morecrews holding the door panel, one on the left, and one on the right, remove the left, and support the door panel while removing the right side. Gently pull the bottom of door panel outward, and the clips on top of door panel will unhinge from top, carefully rotate left side of door panel to floor, and note the wire connections on switch, and orientation of switch, then unplug wires, and move door panel to a comfortable working positon. Door must be open to remove switch, then depress the two plastic retaining keepers on each side of switch, and push switch through toward door. Replace with new switch, reconnect the wires, and reassymble in reverse order. Remember, door assymbly must be inserted in dryer top at an angle, and then bottom rotated downward, and bottom panel nylon guildes inserted into door panel bottom.
Unplugged the washing machine and turned off the water to the machine. Removed the two front covers; unhooked the two front springs; removed the (4) motor mounting bolts; unhooked the two hoses for the water pump; unhooked the wiring harness; removed the belt from the driven pulley; pulled the motor assembly out; removed the (3) screws t
... Read moreo separate the water pump from the motor; removed the belt from the motor pulley; installed new belt and repeated above in reverse to put everything back together; started washing machine and it worked great.