Models
>
MDB4949SDZ0
MDB4949SDZ0 Maytag Dishwasher - Overview
Sections of the MDB4949SDZ0
[Viewing 11 of 11]Keep searches simple, eg. "belt" or "pump".
Lower Dishrack Wheel
PartSelect #: PS3406971
Manufacturer #: W10195416
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
$46.04
In Stock
Rack Track Stop
PartSelect #: PS11746591
Manufacturer #: WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$7.71
In Stock
Door Balance Link Kit
PartSelect #: PS972325
Manufacturer #: 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$33.12
In Stock
Mounting Bracket
PartSelect #: PS11745496
Manufacturer #: WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$10.04
In Stock
Dishwasher Drain Pump
PartSelect #: PS11753379
Manufacturer #: WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
$91.96
In Stock
Dishwasher Door Seal
PartSelect #: PS12348515
Manufacturer #: W11177741
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
$67.53
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Dishrack Adjuster and Wheel Assembly
PartSelect #: PS11756470
Manufacturer #: WPW10571738
This dishrack adjuster and wheel assembly is for dishwashers and lets you adjust the dishrack height and attaches the track wheels to the dishrack.
$28.96
In Stock
Dishwasher Heating Element
PartSelect #: PS9494999
Manufacturer #: W10703867
The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.
$87.69
In Stock
Seal
PartSelect #: PS11731683
Manufacturer #: W10864081
This is a seal, but you may also know it as a door gasket and it is for your dishwasher. The seal forms a watertight barrier between the door and the dishwasher tub, deterring water from escaping duri...
$76.98
In Stock
Water Inlet Valve
PartSelect #: PS11752927
Manufacturer #: WPW10327249
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$74.60
In Stock
Drain Hose
PartSelect #: PS2358130
Manufacturer #: 8269144A
This drain hose is 6 and 1/2 feet.
$31.60
In Stock
Questions And Answers for MDB4949SDZ0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- 2
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jackie
February 2, 2020
My dishwasher will run for 1 minute and 30 seconds. Time then goes to dashes and blinks (- -:- -) then goes to 0:02 and runs until complete. These last 0:02 seem to be it draining.
For model number MDB4949SDZ0
Hi Jackie,
Thank you for your question. If the dishwasher is not running correctly, there may be an issue with either the user control and display board or the electronic control board. Check the connections between the parts to see if they are fitted correctly and check the boards for signs of damage, wear or burn marks. If the boards display any of these signs, replace them. Check the door latch as well. Make sure the door is shut. If the door is not shutting correctly or it may cause this. We hope this helps. Thank you and have a great day.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Kim
December 7, 2021
We’ve had the dishwasher for a few years. It worked great at first but know it doesn’t seem to clean the dishes very well. We use Jet Dry and Cascade platinum any suggestions?
For model number MDB4949SDZ0
Hello Kim, thank you for writing. We have researched the model you have provided and have found the part you are looking for is Manifold PartSelect Number PS11756472. If the manifold is damaged, the spray arm will not be able to wash the dishes in the dishwasher evenly. If you notice that your dishwasher is not cleaning the way it should, it is an indication that you should check the manifold for damage. Good luck and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Kim
December 28, 2019
Dishwasher starts then shuts off after a few minutes
For model number MDB4949SDZ0
Hi Kim, this is usually caused by a faulty pump, door latch, or control board. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Related Parts:
Kim
January 22, 2020
Dishwasher starts, runs for about 2 minutes, then cancels and drains and shuts off.
For model number MDB4949SDZ0
Hello Kim, thank you for your question. We would recommend testing the following parts. PartSelect Number: PS11750035 Thermostat, PartSelect Number: PS9494999 heater, and sensor, PartSelect Number: PS12070543. If these parts are fine, the circulation pump and board should be tested. I hope this helps.
Was this helpful?
Thank you for voting!
William
September 23, 2022
Hi. Thank you for this opportunity. The dishwasher, model MDB49495DZ0, will not energize. This happened after a power outage during the storm. When power to the house was restored, The dishwasher remained dead. I welcome your strong technical kung-fu.
For model number MDB4949SDZ0
Hello William, thank you for your question. We have researched your model and found that the issue is probably with the User Control and Display Board, part number PS11769413. If that does not take care of the issue, then the problem is most likely to be related to the Main Control Board, part number PS11769633. We also recommend checking the power cord of the unit. If you require assistance to place an order, please contact customer service. We hope that helps!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- Next >
Common Symptoms of the MDB4949SDZ0
[Viewing 10 of 10]Leaking
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Parts Used:
-
Scott from Fort Lauderdale, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
623 of 662 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more
the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Read less
Parts Used:
-
Andrew from Alexandria, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
476 of 529 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door spring link broken
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i ... Read more nput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
5. Reverse (2 to 1) to reinstall the dishwasher.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i ... Read more nput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
5. Reverse (2 to 1) to reinstall the dishwasher.
Read less
Parts Used:
-
Sean from Ramona, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
153 of 178 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!