This door switch is for dishwashers.
The door switch detects when the door is closed so the dishwasher can start.
Unplug the dishwasher or shut off the house circuit breaker before installing th...
This part is the replacement drain check valve for your dishwasher. It is made of black plastic and is approximately 1-1/4 inches by 1-1/4 inches. The round section of the check valve is approximately...
This is a leak sensor designed for use with a range of Samsung dishwashers. This sensor is designed to detect if water begins leaking from the water supply. If/when it detects a leak, it stops the wat...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Walter
February 10, 2020
D/w will not work, as if no power. I have checked and all circuits are good
For model number DW80K5050US
Hello and thank you for writing.
It certainly sounds like it could be a faulty door latch and switch PS8764558 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
Hello Maite, thank you for your question. The first step is to determine where the leak is coming from. If its coming from the door, check the door seal, the inner door panel and the water level in the tub. If the leak is coming from under the unit, you will want to check the hoses, the pump and motor, and the water valve. I hope this helps.
Was this helpful?
Thank you for voting!
Christopher
January 27, 2020
The dishwasher keeps draining and will not engage the the motor
For model number DW80K5050US
Hello Christoper, thank you for your question. We would recommend unplugging or turning off the power at the power source, to see if the unit will reset. If the unit does not reset, we would recommend testing the following parts. The turbidity sensor, float switch, and drain pump. If those parts are ok, the issue could be the main control board. I hope this helps.
The dishwasher lights up but won’t start. I reset button on wall for plug in. Turned it of and restated but still won’t start
For model number DW80K5050US
Hello, Thank you for your question. You will want to check on the door latch and the control board. Those are typically the cause of this issue you are having. We hope this helps.
Was this helpful?
Thank you for voting!
Frank
July 5, 2021
No power
For model number DW80K5050US
Hello Frank, Thank you for the question. If the Power Cord, Outlet and Breaker are all tested good, we suggest replacing the Control Panel PartSelect Number PS12072673. We hope this helps!
This is not a repair for the faint of heart. You will have to pretty much disassemble the entire dishwasher to replace the main pump assembly. And it’s not cheap, between the pump assembly and the hose...it was over $300...
This dishwasher is Junk...been through 2 motherboards, plastic internal spray arms...and finally a pump a
... Read moressembly...if you own one and the pump begins to leak....shorts the pump motor out....if it gets this far...but a new dishwasher.
The install definitely takes a bit more than the video I watched but in the end all was fine. The electrical and hose connections are nothing but getting the three screws and retainers isn't as easy as shown in the video I watched and getting them back in is even worse. My hands aren't small but they're not huge either. You'll need multip
... Read morele phillips head screwdrivers. All a #2 head, with one stubby, one about 6" and one long one with about 8" or more of shaft on the screwdriver to remove the screws. Also take pictures if possible with your phone for reconnecting all your wiring harnesses will prove helpful. The only other difficult part of doing it by yourself is compressing the new sump seal enough to get the three nylon retainer clips back into place. There is really need or room for two people on any part of this other than at that point. If you could have somebody push down on the pump unit from inside while you install the retainers it would make it so much easier but I managed. Other than that not a big deal. Good luck!
Repair was fairly simple. Remove torx screws making sure that front control panel does not separate too much from door panel. Not a big deal if it does, just a little more work when putting it back together. Replacing broken part is plug and play. Reseat door panel and control panel and secure with previously removed torx screws. I’ve pro
... Read morebably made it sound a bit more complicated than is really is.