This door switch is for dishwashers.
The door switch detects when the door is closed so the dishwasher can start.
Unplug the dishwasher or shut off the house circuit breaker before installing th...
This part is the replacement drain check valve for your dishwasher. It is made of black plastic and is approximately 1-1/4 inches by 1-1/4 inches. The round section of the check valve is approximately...
This drain hose is 80" long. The drain hose carries drain water from the dishwasher drain pump to the kitchen sink drain.
A/S-DRAIN HOSE OUT;ODM, DW3000MM
This is a leak sensor designed for use with a range of Samsung dishwashers. This sensor is designed to detect if water begins leaking from the water supply. If/when it detects a leak, it stops the wat...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
12 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
February 22, 2020
Water not coming on auto and heavy lights flashing, on panel
For model number DW80J3020US
Hello Michael, thank you for your question. This error is in relation to a water issue. We would recommend testing the water valve, flow sensor, leak sensor and PCB board in that order. The part numbers are below. I hope this helps.
The bottom spray unit that spins came off and it won’t clip back on not sure what parts I need.
For model number DW80J3020US
Hello Brady, Thank you for the question. The Lower Arm, PartSelect Number PS8753319 might be worn or damaged and need to be replaced. We hope this helps.
Once unit is set to wash it sounds like it’s getting ready to to start operation then auto light goes on and nothing happens
For model number DW80J3020US
Hello, Thank you for your question. Here is a link that will show you different parts to look into that would cause the issue you are having- https://www.partselect.com/Repair/Dishwasher/Will-Not-Start/ . We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Dan
February 7, 2020
My daughters Samsung dishwasher fills with water pulses a few times low water lite is on and than the water goes out.You tube said maybe a water level switch.
when my daughter moved in her house the owner said it was new as i have been checking it warranty went off in 2016. so it’s not a 2019 model
For model number DW80J3020US
Hi Dan. The water level switch is likely the correct part. Thank you for your question and good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Amanda
October 27, 2021
My dishwasher won't even power on! Help!
For model number DW80J3020US
Hello Amanda, thank you for writing. First make sure the dishwasher is properly plugged in. Confirm that the dishwasher's power switch is turned on. Check for tripped breakers in the electrical box. If all of these are good check the Door Latch and Switch Assembly PartSelect Number PS8764558 or the Main Power Control Board PartSelect Number PS11720391. We hope this helps.
The install definitely takes a bit more than the video I watched but in the end all was fine. The electrical and hose connections are nothing but getting the three screws and retainers isn't as easy as shown in the video I watched and getting them back in is even worse. My hands aren't small but they're not huge either. You'll need multip
... Read morele phillips head screwdrivers. All a #2 head, with one stubby, one about 6" and one long one with about 8" or more of shaft on the screwdriver to remove the screws. Also take pictures if possible with your phone for reconnecting all your wiring harnesses will prove helpful. The only other difficult part of doing it by yourself is compressing the new sump seal enough to get the three nylon retainer clips back into place. There is really need or room for two people on any part of this other than at that point. If you could have somebody push down on the pump unit from inside while you install the retainers it would make it so much easier but I managed. Other than that not a big deal. Good luck!
Repair was fairly simple. Remove torx screws making sure that front control panel does not separate too much from door panel. Not a big deal if it does, just a little more work when putting it back together. Replacing broken part is plug and play. Reseat door panel and control panel and secure with previously removed torx screws. I’ve pro
... Read morebably made it sound a bit more complicated than is really is.
Removed front panel, removed lower plates to expose power source, Found wire broken to front panel. Part of 1 wire missing about 2 inches. Maybe a mouse. Replaced harness and machine working now.