Models > AWN311SP111TW01 > Symptoms > Noisy

Parts That Fix Speed Queen Washer AWN311SP111TW01 Noisy

Noisy is a commonly reported symptom for the AWN311SP111TW01 Speed Queen Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your AWN311SP111TW01 Speed Queen Washer that will fix Noisy. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

1 Thrust Washer
Fixes Symptom 60% of time
Thrust Washer – Part Number: WP233520
★★★★★
★★★★★
2 Reviews

Rated by 37 customers 

  

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.

$ 7.97
  In Stock
PartSelect Number PS11740482
Manufacturer Part Number WP233520

Replacing your Amana Dryer Thrust Washer

Replacing your Thrust Washer

Customer Repair Stories

Clanging of dryer when rolling

Followed video on PartsSelect website, they made it real easy.
  • John from Bel Air, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

belt was cracking and dryer was somewhat noisy

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.
Read less
  • Melody from Silverton, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Retaining Ring
Fixes Symptom 39% of time
Retaining Ring – Part Number: WP23748

Rated by 35 customers 

  

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.

$ 13.61
  In Stock
PartSelect Number PS11740487
Manufacturer Part Number WP23748

Replacing your Amana Dryer Retaining Ring

Replacing your Retaining Ring
3 Wave Washer
Fixes Symptom 1% of time
Wave Washer – Part Number: WPY504082

This is the replacement wave washer for your washing machine. It is approximately ¾ inch in diameter. This washer is sold individually and is an authentic OEM part.

  No Longer Available
PartSelect Number PS11757550
Manufacturer Part Number WPY504082
Back to Top