This rack adjuster kit (Dishrack Adjuster Kit, Adjuster Kit, Dishwasher Rack Adjuster) will adjust the height of the upper rack of your dishwasher. It connects to the dishrack. The kit is constructed...
$46.75
In Stock
Order within the next 11 hrs and your part ships today!
This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and fal...
$8.12
In Stock
Order within the next 11 hrs and your part ships today!
This manufacturer-certified heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dish...
$66.28
In Stock
Order within the next 11 hrs and your part ships today!
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$10.06
In Stock
Order within the next 11 hrs and your part ships today!
This one-piece door gasket provides a water tight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking, tears, or there are gaps in your ...
$76.57
In Stock
Order within the next 11 hrs and your part ships today!
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
$38.32
In Stock
Order within the next 11 hrs and your part ships today!
This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack wil...
$49.67
In Stock
Order within the next 11 hrs and your part ships today!
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
$92.13
In Stock
Order within the next 11 hrs and your part ships today!
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
$46.17
In Stock
Order within the next 11 hrs and your part ships today!
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
$7.77
In Stock
Order within the next 11 hrs and your part ships today!
The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is...
$67.38
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for 66513049K111
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Replacement was pretty easy after figuring out how to unsnap/unlock the old pieces. Tools only used to do a little prying and poking, but really aren't needed. Everything either snaps or slides together. Piece of cake
I took the broken basket adjuster off and then attached the new one. It wasn't too difficult, however some removal instructions and re-install instructions( or just a picture supplied) would have been helpful. This isn't an issue for a mechanically inclined person, but would be a challenge for someone that isn't. Thanks.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.