Kenmore Dryer Ducts and Vents

Your Price

$89.91

Kenmore Dryer Air Duct

★★★★★

2 Reviews

PartSelect Number PS11775712

Manufacturer Part Number 5304508449

Fixes these symptoms

Marks left on clothes
See more...

Installation Instructions

Rich from New Albany, OH

Internal vent inside the drum was coated in black (plastics from use)

1. Loosened the 3 screws inside of the drum
2. Removed the entire back of the dryer (lots of screws)
3. Removed the old vent (there are 2 screws at the bottom that hold it in)
4. Install new vent (put the screws back in)
5. Close up back and proceed to put all of the screws back Read more...

Your Price

$132.19

Kenmore Dryer Lint Screen Grille

★★★★★

4 Reviews

PartSelect Number PS12114312

Manufacturer Part Number W11117302

This part is the replacement lint screen grille for your dryer. It is made of white plastic and is approximately 21 inches by 7 inches. The lint screen grille fits inside the lint screen housing and prevents clothing from falling into the lint duct. The main reason you would want to replace the lint screen grille would be if it is cracked, damaged, or missing, as clothing may be able to slip into the lint duct. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Installation Instructions

Luis from FRESNO, CA

High pitch noice

Raised the front of top panel with the putty knife and the front panel was unscrewed as the video showed. The drum slid out after the belt was released.

My machine had 4 rollers, which was not shown in the schematics. So I replaced the back, cleaned the front ones and works great for now. Plan to replace the front later.

Removing the tri rings is much easier if cut w wire cutters. Otherwise waist lots of time to get them off. Just buy new ones. Read more...

Videos!

Your Price

$163.10

Kenmore Dryer Box, Heater

★★★★★

3 Reviews

PartSelect Number PS11746303

Manufacturer Part Number WP8541818

The heating element is not included with this box.

Fixes these symptoms

Marks left on clothes
See more...

Your Price

$22.53

Kenmore Dryer Guide,Filter

PartSelect Number PS3524629

Manufacturer Part Number 4974EL1003B

The filter guide is found in your dryer and is what houses and supports the lint screen located in the exhaust air duct. This part is located at the bottom part of the dryer opening. The housing is approximately 14 inches long and 5 inches wide, with a moon shape on the top where the lint trap goes. The filter guide may break of wear down over time and with repeated use, and may need to be replaced. This OEM part comes right from the manufacturer and is sold individually.

Installation Instructions

George from Croton on Hudson, NY

The holder for the lint screen was removed to vacuum lint. It broke when turned on.

I found that the screws that hold it in were a bit too short. After several cleanings I re inserted the screen only to have it dislodge and break. I ordered a new part and after using a drift pin and lamp I found that the screws were too short and the threads needed to secure it were worn. Longer screws solved the problem. Read more...

Your Price

$106.33

Kenmore Dryer Side Venting Kit

★★★★★

1 Review

PartSelect Number PS3489583

Manufacturer Part Number W10323246

This is a four way dryer vent kit.

Installation Instructions

Dodd from Fort Worth, TX

I was adding a 4-way vent to side vent the dryer

Doing my home work, I was told if I was "handy with my hands" I could do the work. Start to finish required 3+ hours. The instructions were not specific to my unit therefore, I had to "guess". My first surprise was encountered on step 2 - removing the top. My top was attached to the "brains" of the drier and therefore could not be removed. I actually had to disconnect the brains to remove the top. My second surprise was that I had to remove just about everything before I could get to the vent, which by the way, was simple. I finally accomplished the task, but.... Read more...

Your Price

$96.55

Kenmore Dryer Heat Duct

PartSelect Number PS12071411

Manufacturer Part Number 5304509715

Videos!

Your Price

$194.88

Kenmore Dryer Side Venting Kit

★★★★★

5 Reviews

PartSelect Number PS3575086

Manufacturer Part Number 3911EZ9131X

This dryer side vent kit lets you vent the exhaust to the side or bottom of your dryer instead of the default rear position. Included in the kit are 2 straight aluminum foil outlet ducts, each 4 inches wide, along with 1 duct elbow, 1 cover plate, 1 screw, and an instruction sheet. This is helpful for flexible installation in areas where rear venting is not possible or practical. All parts are genuine replacements from their original manufacturer.

Installation Instructions

ROBERT from DAWSONVILLE, GA

Install aftermarket side vent kit

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came. Read more...

Your Price

$89.47

Kenmore Dryer Heat Duct Assembly

★★★★★

1 Review

PartSelect Number PS3526481

Manufacturer Part Number 5209EL1001E

Your Price

$197.57

Kenmore Dryer DUCT-AIR

PartSelect Number PS11741422

Manufacturer Part Number WP3387911

Installation Instructions

Thomas from Edgartown, MA

Screen on the hot air vent disintegrated

It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.

The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order

I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones. Read more...