Ice Maker Ice Makers

Ice Maker Refrigerator Assembly

★★★★★

★★★★★

81 Reviews

This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Ice Maker Replacement

★★★★★

★★★★★

150 Reviews

This ice maker (Ice Maker Assembly, Refrigerator Ice Maker) produces ice cubes that are ejected into the storage bucket. It is located in the freezer section of your appliance, mounted on the freezer wall. The ice maker can break from normal wear and accidental damage. If this happens, your refrigerator may no longer make ice cubes, or may not make enough cubes, and the part should be replaced. This model measures approximately 11 inches long and 5 inches wide. It’s constructed of plastic and metal, and comes in black/white/silver. This assembly includes the ice mold and the control device.

Ice Maker Replacement

★★★★★

★★★★★

220 Reviews

This ice maker (Complete Icemaker Assembly, Whirlpool Icemaker Kit, Ice Maker Assembly, Refrigerator Ice Maker, Icemaker) receives water from the water inlet valve, freezes it, and dispenses it into the ice bucket until the bucket is full. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage, and water quality. You can perform a voltage test with a multimeter or perform an inlet valve test. If you’re unable to make ice, or notice leaks then it may be a sign your ice maker is damaged and could be in need of a replacement. This model measures approximately 11x5 inches, is constructed of plastic and metal, and comes in black/silver. This ice maker is a complete assembly; the whole assembly attaches to the wall of your freezer.

Ice Maker

★★★★★

★★★★★

77 Reviews

This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.

Ice Maker Bin Temperature Sensor

★★★★★

★★★★★

14 Reviews

This bin temperature sensor is for ice makers. The bin temperature sensor monitors the temperature in the ice maker bin and sends the temperature reading to the electronic control board. Disconnect the power before installing this part. Wear work gloves to protect your hands.

Ice Maker Replacement

★★★★★

★★★★★

28 Reviews

This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female, and one round male connectors. The tools you will need in order to make this installation include a 1/4-inch nut driver, and a Phillips screwdriver. Before starting this repair make sure to unplug your refrigerator and shut off the water supply.

Ice Maker Ice Cutter Grid Complete Assembly

★★★★★

★★★★★

10 Reviews

If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker and contains thin, heated wires that slice the ice into cubes that are then deposited in the ice bin. If the cutter grid is broken, ice can back up within the ice maker. This part is sold as a complete assembly and is used with freestanding ice makers. Be sure to wear work gloves to protect your hands when completing this repair. This is an OEM part that sources directly from the manufacturer.

Ice Maker Ice Bucket - White

★★★★★

★★★★★

12 Reviews

The ice bucket in your freezer collects the ice from the ice maker and stores it. If your old ice bucket is damaged you may want to replace it as it can leak. This product is made of white plastic and is approximately 13 inches in length and 9 inches wide at the widest point. This is an OEM part sourced directly from the manufacturer. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the damaged bucket, making sure to collect any broken pieces. Then, simply slide the new bucket in place.

Ice Maker Drive Gear

★★★★★

★★★★★

7 Reviews

The ejector drive gear is a part for your refrigerator. This icemaker drive gear is for the ejector blades. The part rotates the cube ejector arm, which cycles the icemaker and pushes the cubes out and into the ice bucket, ready for the ice to be used. The outside diameter of this piece is almost two inches by two inches. The reason for needing to replace your gear is if the current one is broken/missing a tooth, or if your icemaker is not dispensing ice and is noisy.

Ice Maker Icemaker Control Assembly

★★★★★

★★★★★

26 Reviews

The “Icemaker Control Assembly” (Module & Motor Assembly, Ice Maker Control Module, Icemaker Module, Refrigerator Ice Maker Module) is what controls the actions of your ice maker. The control turns the timing cams and the ejector blades. It controls most of the basic parts and functions such as the heater, water inlet valve, the cube size, and cube ejection. If your ice maker control is broken it can no longer properly control the ice maker functions. It may not produce any ice, make small ice cubes, or have intermittent operation. This can occur due to normal wear and tear. The icemaker control assembly is attached to the ice maker mold, and is under the white cover. Test the icemaker control assembly by using a multimeter. If this reveals the assembly to be defective, you will need to replace this part. It is approximately 4.25 inches square, beige, and is constructed of plastic and metal. This replacement part features one icemaker control assembly, including the control module and the motor.