Dryer Legs and Feet

Dryer Leveling Foot

★★★★★

★★★★★

13 Reviews

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.

Dryer Foot, Front - Single

★★★★★

★★★★★

4 Reviews

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.

Dryer Adjustable Leveling Foot - Black This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling, it may indicate that the levelling foot needs to be replaced. You will need pliers and a block of wood to perform this task. There will be one adjustable foot found in the package. Lift the dryer and place the wood to keep it propped up. You may need to use the pliers to remove the old foot. Screw the new foot into place using your hand. Once the new leveling foot is in place, lift the appliance and remove the block. Test the machine out to ensure it is now sitting level.

Dryer Rubber Foot Pad

★★★★★

★★★★★

1 Review

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers. Many of our customers have rated this repair as very easy. To complete the repair, turn the old leg counter clockwise to remove it. Then, simply remove the old pad and replace it with the new one. Finally, re-attach the leg by turning clockwise. Ensure that the washer is level, and adjust the leg accordingly if it is not.

Dryer Rubber Leveling Leg Foot Pad

★★★★★

★★★★★

1 Review

This gray levelling leg foot pad is made of rubber and is just over an inch in diameter. Sold individually.

Dryer Levelling Feet, Pack of 4

Dryer Adjustable Leveling Screw

★★★★★

★★★★★

2 Reviews

The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able to create a level base for your dryer. The leveling screw has a hexagon-shaped gray plastic foot, with a screw that is approximately 1 inch in length. To replace a damaged screw, simply turn the old screw to the left, until it can be removed. Then, simply screw the new leveling screw into place on the bottom of the dryer, making sure it is the same height as the other 3 leveling screws.

Dryer Adjustable Leveling Leg

★★★★★

★★★★★

1 Review

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

Dryer Leveling Foot & Nut This individual levelling foot is compatible with different types of standing home appliances and is a genuine OEM part. Made of high-quality metal and featuring a metal securing nut, this levelling foot is made of plastic and is used to level the pedestal for your appliance. Over time and through gradual wear and tear of moving your appliance around or through excessive movement and impact, a levelling leg will crack and break, and eventually destabilize itself. If you find your appliance is imbalanced or vibrates excessively when in use, this levelling foot may need to be replaced. Since most appliances take one foot on each corner, 4 corners being 4 feet, it is important to consider the amount of feet you require when ordering. This levelling foot is adjustable, since it comes with the securing nut, adding longevity to the levelling foot and your appliance. To replace this foot, simply lift the corner of the pedestal from the floor, unscrew and remove the previous foot, and install the new foot, adjusting its height with the nut.

Dryer FOOT