Whirlpool Washer Dryer Combo Seals and Gaskets

Whirlpool Appliance Parts

Popular Whirlpool Washer Dryer Combo Seals and Gaskets

Your Price
$47.36
  In Stock
Whirlpool Washer Dryer Combo Dryer Drum Seal with Adhesive
★★★★★
★★★★★
19 Reviews
PartSelect Number PS970088
Manufacturer Part Number 280114
This drum seal with a silicone rubber adhesive is used in dryers. This part seals the drum to make sure air does not escape from the dryer. If your dryer is making loud noises, is not producing enough heat, or no heat at all, or there are marks left on your clothes, replacing the seal on your dryer can solve the problem. The tools needed for this installation project are: 1/4 inch nut driver, Phillips screwdriver, small flat blade screwdriver, and putty knife. Remember to unplug your dryer from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for installation instructions.
Fixes these symptoms
Installation Instructions
Jerry from Everett, WA
Rear tub seal failure
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine Read more...
Your Price
$9.78
  In Stock
Whirlpool Washer Dryer Combo Lint Trap Housing Seal
★★★★★
★★★★★
8 Reviews
PartSelect Number PS11741506
Manufacturer Part Number WP339956
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint chute and the bulkhead of your appliance. This foam seal is just over 28 inches long and under 1 inch wide. You may need to replace this part if your clothing is taking too long to dry, or if your dryer is not generating enough heat or no heat at all.
Fixes these symptoms
Installation Instructions
Eric from Fort Dodge, IA
dryer drum not turning and no air circulating
replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot. Read more...
Your Price
$5.77
  In Stock
Whirlpool Washer Dryer Combo Centerpost Gasket
★★★★★
★★★★★
6 Reviews
PartSelect Number PS11723081
Manufacturer Part Number W10814296
This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, and made of plastic material. To perform this repair, you will need to disconnect the power, drain hose, and the inlet hose. You will need to remove the entire outside cabinet to have access to the tub assembly. The tub will need to be removed entirely. This is a genuine part that is sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...
Your Price
$7.70
  In Stock
Whirlpool Washer Dryer Combo Washer
★★★★★
★★★★★
1 Review
PartSelect Number PS11742027
Manufacturer Part Number WP3949550
This part goes on the agitator retaining bolt.
Fixes these symptoms
Installation Instructions
Patrick from Marysville, WA
The upper agitator arm would not rotate
It was extremely easy. I removed the plastic cap under the softener dispenser, removed the nut and washer that holds the upper agitator in place and then replaced the parts that came in the kit. The most important note for those who may be doing this job is that the o-ring for the cap under the softener dispenser, the seal washer for the bolt and the thrust spacer under the upper agitator all came with the kit. I did not realize that and ordered them all seperately. Read more...
Your Price
$11.12
  In Stock
Whirlpool Washer Dryer Combo Seal, Inner Cap
★★★★★
★★★★★
11 Reviews
PartSelect Number PS11748108
Manufacturer Part Number WPW10072840
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inches in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Leaking
  • Spins slowly
  • See more...
Installation Instructions
Lennis from Jacksonville, NC
Would not agita.
It was a blessing that I ordered the kit, because I thought it only needed the rubber seal and the four dogs. But because the seal and dogs cost less than the shipping I decided to order the kit and its good I did because the nochage on the basket sleeve was broke off. The blessing is that the sleeve was in the kit, sp it took 5 sec to slip it on along with the rest of the kit, and after about 15 min my wife was back to work. Thanks for saving me time and money without this web site I would have bought another brand new washer, thanks. Lennis from NC. Read more...
Your Price
$11.12
  In Stock
Whirlpool Washer Dryer Combo Washer Transmission Stem Seal
PartSelect Number PS11746747
Manufacturer Part Number WP8577376
Sold individually.
Fixes these symptoms
Installation Instructions
Bob from East Palestine, OH
The motor turned with loud noise ,but nothing else worked
I used "Emley's Cheap and Easy Repair" book to remove,install and reassemble the machine.
A lot of time was used to clean the filthy tub and basket.
While replacing the broken motor coupling I decided to replace some of the seals.
PartSelect got the ordered parts to me in a couple of days.
I wouldn't hesitate to do the job again.
Read more...
Your Price
$11.12
  In Stock
Whirlpool Washer Dryer Combo Blower Housing Seal
★★★★★
★★★★★
4 Reviews
PartSelect Number PS11743810
Manufacturer Part Number WP697770
This part seals between the blower housing and the blower housing cover.
Fixes these symptoms
Installation Instructions
Tammy from PINEVILLE, MO
wouldn't heat
watched videos on this site Read more...
Your Price
$8.02
  In Stock
Whirlpool Washer Dryer Combo SEAL-SHAFT
★★★★★
★★★★★
1 Review
PartSelect Number PS11746864
Manufacturer Part Number WP91939
This OEM upper transmission shaft seal, also known as the oil seal, is found in your washers and dryers. It acts as a barrier to prevent water from leaking into the transmission assembly. It measures 1/2 inch in height with a 1-inch diameter, and is located at the top of the transmission shaft where it enters the tub. Signs of a broken seal include water stains, dampness, or pooling of water beneath the appliance. If left unreplaced, it can result in water damage to internal components, along with the potential for corrosion, mold growth, and unpleasant odors. To remove the shaft seal, consult your user guide for specific instructions. Start by shutting off the power and water supply. Remove the water hoses and drain hose, being cautious of any water that may leak out. You will need tools like a putty knife, screwdriver, nut driver, pliers, spanner, plastic mallet, and a socket set. Open the lid and proceed to remove the agitator assembly, detach the control panel, and disconnect any necessary wiring harnesses. Remove the cabinet and water break. Continue disassembling the inner tub until you can lift it out of the appliance and tilt it onto its back, propping it up with a block. This will allow access to the transmission assembly from beneath the appliance. Remove the mounting fasteners on the pump to reach the motor assembly. Once the motor assembly is out, further disassemble it to access the basket drive. The seal can be removed from the top of the shaft of the drive tube, below the thrust ring. When purchasing parts for your appliance repair, it is important to remember that your appliance uses various seals and gaskets. It is important to ensure that you purchase the correct part when making repairs.
Fixes these symptoms
Installation Instructions
Al from OCEAN, NJ
drive shaft leaking
Washer was leaking -- in part from hoses that had loosened over time due to unbalanced loads and age, and partly from a worn pump -- and not agitating/spinning properly. Fixed hoses, replaced pump and clutch. Unfortunately, when I pulled apart direct drive to replace clutch, the drive shaft started leaking because old seals worn and compromised on disassembly. Have to give credit where due -- YouTube invaluable here -- pulled and disassembled drive shaft, removed old seals, replaced and reassembled. Time consuming, but if you keep track of where things go, not too bad. 3 things I wish I knew in advance: (1) for an old washer you definitely need a spanner nut wrench (like 15-25 bucks online) to remove the spanner nut so you can pull the basket and get to the seals -- no wrench/pliers/vise substitute will do the trick; (2) the shaft seals have metal washers inside the rubber/plastic -- when you're removing the old seals, you might need to chisel (hammer and small flat head screwdriver) the old seals out instead of just pulling out the corroded rubber which will leave the old metal behind; (3) if your time is valuable, try to diagnose all the likely sources of your problem and buy the parts to repair at once rather than doing piecemeal like me. Took me 2 weeks and two complete tear downs to finish a repair that should have taken me an afternoon. I love my local Appliance Parts guy -- he's knowledgeable and usu. has what I need or can get it fast and I like supporting local brick and mortar -- but if time is important to you, taking advantage of online companies that allow you to return what you don't use may save you time. Read more...
Your Price
$8.30
  In Stock
Whirlpool Washer Dryer Combo Hose Washer Kit
PartSelect Number PS1803069
Manufacturer Part Number 285452A
Washer fill hose gasket and screen. This is a set of 4.
Your Price
$55.71
  In Stock
Whirlpool Washer Dryer Combo Bearing and Seal Kit
★★★★★
★★★★★
2 Reviews
PartSelect Number PS334171
Manufacturer Part Number 279264
This front bearing and seal kit comes with the adhesive.
Fixes these symptoms
Installation Instructions
Leslie from Townsend, GA
Drum was binding because of worn bearing supporting front of dryer drum
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to glue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!! Read more...

Related Whirlpool Washer Dryer Combo Parts