Kenmore Dryer Drums and Tubs

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Kenmore Appliance Parts
Shop By Part Type

Popular Kenmore Dryer Drums and Tubs

Videos!
Your Price
$14.29
  In Stock
Kenmore Dryer Drum Bearing Slide - Green (Sold individually)
★★★★★
★★★★★
27 Reviews
PartSelect Number PS6447706
Manufacturer Part Number WE1M1067
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from regular use. As the slides start to break down it may cause your dryer to make noise or not dry clothes in the usual amount of time. You will need to purchase two for both sides of your dryer. They attach to the outer-most sides of the bearing. The manufacturer recommends replacing both slides at the same time. Take this opportunity to clean out the lint and dust in the dryer, to keep it running smoothly. This is a genuine replacement part that comes directly from the manufacturer. This item is sold individually. The part attaches to the outermost side of the bearing. Although this part is denoted as being "Green" in its title, many users and technicians have noted that its true colour is closer to a dark gray or black.
Fixes these symptoms
Installation Instructions
Matthew from Plainfield, IL
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy. Read more...
Videos!
Your Price
$18.58
  In Stock
Kenmore Dryer Drum Bearing Slide - White (Sold individually)
★★★★★
★★★★★
157 Reviews
PartSelect Number PS755842
Manufacturer Part Number WE1M504
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from regular use. The part attaches to the outermost side of the bearing. Check both slides for signs of wear, because they often wear at the same rate, and should be replaced at the same time; there are 2 of these particular slides per dryer. This part is sold individually, so you'll need to purchase multiple parts if replacing both at the same time.
Fixes these symptoms
Installation Instructions
Matthew from Plainfield, IL
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy. Read more...
Videos!
Your Price
$34.80
  In Stock
Kenmore Dryer Upper Drum Glide
★★★★★
★★★★★
28 Reviews
PartSelect Number PS470317
Manufacturer Part Number 5303937139
The upper drum glide is attached to the front panel of your dryer, you can locate it by removing the top portion of your dryer. The drum glide allows the drum to rotate with ease and little sound. The front upper felt glide pad with three nylon glides also includes adhesive, essential for mounting accurately. For this project you will need a putty knife, Phillips screwdriver, and a wire brush. This repair is meant to fix issues such as an abnormal amount of noise or the dryer not tumbling as it should. Consider replacing your belt at the same time if you have a dryer more than 5 years old, as it is likely worn.
Fixes these symptoms
Installation Instructions
Matthew from Portland, OR
Clothes getting scorch marks, drum noise
First and foremost, I read the repair reviews here at parts source and found that a) Other people had the same symptoms, b)following their repair tips made it super easy.
What I would add to previous reviews is to pull the front off or the little acces grill in back and check to see what kind of belt you have. According to the model #, It showed the wide flat belt when in fact I had the smaller ribbed belt. Glad I checked before ordering.
A few things that will make your life easier is once you have the old upper guide/seal removed, put down the glue then use several med sized plastic spring clamps to hold the seal in place while the glue sets up, (@ 20-30 min). Their cheap and you should have some around anyway. When replacing the seals I would go ahead and replace the belt too. It's cheap and if your machine is 5+ yrs old probably is worn. Total cost of repair was about $60 (inc shipping). Took about 1 hr 20 min total time. Most of that time was scrapping the old seal material/ glue off the dryer front. Actual disassembly and repair maybe 1/2 hour. Other little tip is the clips for the lid of dryer is to use a flat screwdriver and gently push straight in until it's compressed enough to release the lid, it will pop up when pushed in far enough. That one took me a while to figure out.
Thanks to Part Select for such a helpful site. My dryer is like new again. Read more...
Videos!
Your Price
$28.03
  In Stock
Kenmore Dryer Drum Glide - White
★★★★★
★★★★★
15 Reviews
PartSelect Number PS5574052
Manufacturer Part Number 137513300
This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each drum glide is approximately 33 inches in length. If the following symptoms occur, consider replacing the drum guide as a solution: dryer is noisy, will not tumble, or leaves marks on clothes. Remember to unplug the power source to the dryer before installing this part. Refer to the diagram provided by the manufacturer for further instructions and guidance.
Fixes these symptoms
Installation Instructions
Sergio from Cromwell, CT
Clothes were getting caught in gap, leaving burn mark.
Took the face off, and replaced the worn down drum glide and felt. Works just fine now. Read more...
Videos!
Your Price
$58.72
  In Stock
Kenmore Dryer Two-Piece Split Ring Bearing
★★★★★
★★★★★
10 Reviews
PartSelect Number PS334199
Manufacturer Part Number 279441
This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during operation, or if there are marks left on your clothes after a cycle, you may need to replace the bearing ring kit. The kit comes with 2 bearings, one for the top and one for the bottom of the dryer drum. Remove the front panel of your dryer to access the dryer drum for this repair. At this point you can use a pair of needle nose pliers to release the old bearing rings from the drum. Snap the new bearing rings on, and reassemble the dryer to complete your repair.
Fixes these symptoms
Installation Instructions
Edward from Andover, NJ
Dryer was sqeaking loudly when running
I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan Read more...
Your Price
$43.83
  In Stock
Kenmore Dryer Rack
★★★★★
★★★★★
1 Review
PartSelect Number PS3521801
Manufacturer Part Number 3750EL1001A
This grey drying rack fits inside your front load dryer. It is an accessory used to dry items that should not tumble, like shoes, stuffed animals, pillows, or other delicate items. It provides a stationary surface for these items to rest on while air circulates. The rack is 27 inches wide and can be attached inside the dryer drum. This genuine OEM rack is sold individually.
Your Price
$38.68
  Special Order
Kenmore Dryer Baffle
★★★★★
★★★★★
7 Reviews
PartSelect Number PS3522961
Manufacturer Part Number 4432EL1002A
Your Price
$29.57
  In Stock
Kenmore Dryer Rack
★★★★★
★★★★★
2 Reviews
PartSelect Number PS3521800
Manufacturer Part Number 3750EL0001C
This dryer rack is compatible with various models of LG top-load dryers. It is approximately 27 inches long, light grey in color and made of durable plastic. The rack is positioned inside the dryer and it is responsible for holding laundry items that can not be tumble-dried. If the rack breaks or otherwise fails, you will be unable to use this feature of your dryer. You do not need any mounting hardware to secure this rack, simply slide it over the appropriate mounting brackets inside the dryer.
Your Price
$59.32
  In Stock
Kenmore Dryer Drum Front Bearing Ring
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11741470
Manufacturer Part Number WP3394509
This part mounts to the front of the drum.
Fixes these symptoms
Your Price
$30.07
  In Stock
Kenmore Dryer Drying Rack - Dimples 9.5" apart
★★★★★
★★★★★
2 Reviews
PartSelect Number PS346509
Manufacturer Part Number 3404351
This Whirlpool/Kenmore made dryer drying rack is great for drying shoes and other items that cannot tumble dry. This dryer rack fits whirlpool made dryers that are 29 inches wide, have the letter "E" following the numbers in the model number, and whose dimples are nine and a half inches apart in the back of the dryer drum.
Installation Instructions
Robert from BLOOMINGTON, IL
I was sent a drying rack for my electric dryer
The drying rack sent matched the dimples,9.5 inches apart, but it was an inch and a half too long. The rack sent was 21 inches, I need a rack that is 19.5 inches long. So I returned it. At TWICE the cost of the rack itself. Still in search of a rack that will fit my dryer Read more...

Related Kenmore Dryer Parts

Back to Top